Search results

  1. alldodge

    Riddle me this Batman.....

    Could get a $3 AF tester
  2. alldodge

    complete Alpha one Gen one retrofit into older boat.

    Missed the "clamp on" forks I have a set of them which I use on my Terramite. The clamp on type can be dangerous because they can pivot side ways. Maybe put them direct next to each other and clamp them so they are more ridged
  3. alldodge

    1988 3.0 and 1994 3.0 swap

    The balancer shows its a 140hp 3.0
  4. alldodge

    Radon and seal concrete under tub

    House built in 1969, probably before Radon was wildly known. This is my Great Aunt/Uncle retirement home and now its ours. Just decided to test it about a year ago. Found somewhat higher readings with the package tester so bought the higher tech electronic unit. Now just want to try some...
  5. alldodge

    Radon and seal concrete under tub

    I can see the entire underside of the front of the tub. If I had a concrete pumper of some kind that might work. Could mix it up real soupy but not sure this would make more a mess then something else I wonder Get some 3 LB foam and setup something I can pour from the rear to the front. The...
  6. alldodge

    Radon and seal concrete under tub

    Will do what I have to do, but that much epoxy looks to be maybe $500
  7. alldodge

    Radon and seal concrete under tub

    Wonder how many gallons it would take Figure a standard tub is 30x60 and don't know if the rear is higher then what I can see. I do have a bore scope so with enough lighting I should be able to make a guess
  8. alldodge

    Radon and seal concrete under tub

    Maybe, like it better then something like Tar. Wounder would expansion and contraction be an issue?
  9. alldodge

    Radon and seal concrete under tub

    In short: Measuring Radon between 4.1 to 4.5 Basement Tub was installed over gravel base. Concrete is all around it and as to why they did it this way is anyone's guess. Have access to drain side of tub and looking for a way to seal under the tub without removing the tub. Think about floor...
  10. alldodge

    complete Alpha one Gen one retrofit into older boat.

    About 300 to 350, the tractor will have no issue so long as the hydraulics on the tractor are ok. A round bail of hay comes in around 1200
  11. alldodge

    Mercruiser 7.4L MPI Alarm won't stop

    This is what's called a soft alarm. Certain MEFI-3 will set a soft alarm below 3000 RPM and it will go to a hard alarm (constant sound) above 3000 RPM. The MEFI-3 engine’s Audio Warning system will sound the alarm differently and it has more items that will cause it to sound. There is what is...
  12. alldodge

    Thunderbolt 5.0 keeps dying

    Might just be a speck of crud in the needle seat. Get it started and see if you see fuel dripping at idle or when its shut off
  13. alldodge

    Engine cooling water in tube bigger than gimbal housng tube

    Item 27, list one for 5/8 and 3/4 https://www.mercruiserparts.com/bam/subassembly/30870/2203/40
  14. alldodge

    Quicksilver 3000 throttle control button install

    Its all controlled in the shifter Didn't happen to swap the cables maybe? Put in throttle only to see if it gives throttle of shifts
  15. alldodge

    Need help with New EST Delco Distributor and coil wiring

    Oh, with points the shift interruptor grounds the coil during shifting. The EST needs 12V applied when shifting. So disconnect the ground side of the switch and connect 12V from the purple wire
  16. alldodge

    1988 3.0 and 1994 3.0 swap

    If i I would do it just knowing g what you have said
  17. alldodge

    5.0gi PEFS stalls and deceleration

    There is something wrong internally with the motor
  18. alldodge

    Engine cooling water in tube bigger than gimbal housng tube

    Its not a mistake, all use a 1.25 ID tube. This works for 3.0 with Alpha drive or 525 HP with Bravo XR drive. Same part for all
Top