Search results

  1. alldodge

    2008 Mercruiser 5.0 tks won't go into drive or reverse

    Did the throttle only button get stuck ingaged?
  2. alldodge

    New valve cover gaskets and still leaking V6 4.3

    Don't see an issue with the oil vapor, all motors do it and the older they get the more it does it
  3. alldodge

    Start

    Then your Bat is bad, the cables and or connections are corroded, or the starter needs replacing.. Have the Bat load tested at local auto parts place
  4. alldodge

    Start

    I don't put a lot of faith in a boats Bat gauge, but your Bat is about dead, can tell that just from the sound of it cranking Get the Bat charge up and try again
  5. alldodge

    Start

    Sometimes the Tach can short out so its good practice if there is no spark to disconnect the wire. This didn't help at this time, but we still don't know if its no spark or fuel. Were going down testing for spark first
  6. alldodge

    Start

    SN and your pic shows TB5 ignition with knock module Run thru this troubleshooting guide "exactly" like it says
  7. alldodge

    12volt not working

    They are breakers and can be reset with Bat ON or OFF, doesn't matter
  8. alldodge

    Cooked my impeller

    Should be 46-96148A8
  9. alldodge

    Thermostat location on 2020 Volvo Penta 4.3L V6 280HP I/O Forward Drive

    Might be able to find it using your serial number at volvopentashop.com
  10. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    No special tools needed, remove the six nuts and pull the drive I only mention to remove the drive because it will make it easier to replace parts with the drive being out. You might be able to replace the part without removing the drive. Raise full up and see if there is room I don't know...
  11. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    Can get yo that part after removing drive
  12. alldodge

    Any way to reset an mpi without rinda tool

    Don't know how to do with 555 other then diacom or techmate
  13. alldodge

    3.0L I/O issue after new shifter was installed

    Suggest contacting NV AG office
  14. alldodge

    Any way to reset an mpi without rinda tool

    Depends on what ECM If its MEFI, turn key ON with jumper in service mode, then move throttle to WOT and return. Turn key OFF, codes should clear
  15. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    Sucking some air Hey @Scott Danforth what do you think?
  16. alldodge

    New valve cover gaskets and still leaking V6 4.3

    If covers and head edges are straight, might clean the surfaces and use some acetone to make sure all the oil is removed, then use some Black RTV in the corners. Put covers on but don't torque right away, finger tight so the RTV comes out some. Next day torque to spec Hope others will come...
  17. alldodge

    New valve cover gaskets and still leaking V6 4.3

    Those are the new style and should not have much issue sealing. The gaskets fits inside a grove on the cover and it uses 3 bolts in the center Need to use a straight edge and see if the cover edge is straight. Like a framing square. Are they both leaking or just one side? Torque shows 106...
  18. alldodge

    New valve cover gaskets and still leaking V6 4.3

    What 4.3, serial number?
  19. alldodge

    Volvo Penta SX - water leak help

    Transom nuts don't back off on there own, your transom is shrinking
  20. alldodge

    Poor man’s boat - 1988 sea Ray weekender 230

    Use exterior grade plywood and your good
View older results
Top