Search results

  1. alldodge

    3.0GS MBYMCE Exhaust manifold leak

    Put a straight edge on the head intake/exhaust ports
  2. alldodge

    Perfectly for 15 minutes then, surging, knocking, and jumping tac

    Vac gauge no, would have trouble finding a place to connect it also on a boat motor
  3. alldodge

    Volvo Penta KAD 300 power steering issue

    Please look at the manual. The cap is removed tube attached to bottle and bottle is upside down feeding helm
  4. alldodge

    Volvo Penta KAD 300 power steering issue

    Need to remove the cap and make sure it stays full
  5. alldodge

    IAC problems

    No expert, but pins B and C are listed as switched. This tells me the ECM grounds those pins to energize the coils. Meaning the other pins have full power when ECM is powered up. The test light will flash because ECM is switching on/off which will cause the like to flicker on either side of...
  6. alldodge

    Volvo Penta KAD 300 power steering issue

    The manual shows to connect the bottle with a tube connected to the fill port. This will let air out and keep oil filled. By turning wheel each way and seeing nothing come out, and then the second time and seeing air and then fluid, would tell me there is air being purged somewhere
  7. alldodge

    Fuel supply module

    The code will help but may not say what is actually wrong, we need clues. Need to know what the fuel pressure reading is. If pressure isn't high enough then full power is not achievable. If its to high then it floods the motor
  8. alldodge

    TBI rebuild help needed

    The TB is a GM part. Look up the Reg for Chevy/GMC truck Not saying this is yours, just what to look for https://truckprousa.com/i-6275406-jet-performance-tbi-fuel-pressure-regulator-kit-61510.html
  9. alldodge

    1997 3175 Rogue Radar Arch

    Most of the manufactures don't keep older year models, or they just don't care. Cruisers does ok but not so much for older. Builders like Formula and Cobalt keep stuff around If you can feel/see the hole try to guess at the diameter. Most bolts will be standard and not fine thread. Guess at...
  10. alldodge

    Volvo penta 5.7 power problem

    Which 5.7 GL maybe what? Is this a new to you boat? Has compression been checked?
  11. alldodge

    Fuel supply module

    Would need to know what the code was. Would also like to know what the fuel pressure output is. Could be any of the components, low/high pumps, regulator or float. There is a shrader valve where the fuel pressure is measured Don't see how the fuel module/pump would have a problem even if it...
  12. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    The more blades = more pitch If you go from 3x3 to 4x3 need to drop more pitch
  13. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    ok, then change up A 4x4 prop set of 18 = a 3x3 prop set of 20 So if you had 3x3 20Pitch you have about the same with 4x4 18Pitch Go with a 3x3 18P
  14. alldodge

    Mercruiser 233 Overheating--Out of Ideas

    Yes you can, get a short piece of clear hose, a double male barbd fitting and couple hose clamps. Remove the hose going into the thermostat housing from the drive and install short hose.
  15. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    Is this a Bravo 1, 2 or 3 drive?
  16. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    Yes 3B 18 but 3B props normally come in odd numbers. If that's the case get 3B 17. If rpms get to high and your on plane go with 3B 19, but start lower first
  17. alldodge

    Mercruiser 233 Overheating--Out of Ideas

    Guess your not moving enough water Have you tried clear hose from drive to see if its drawing air (bubbles)
  18. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    Post 1 list Post 91 now So if you originally had a 3 blade 20 and changed to a 4 blade 18, for the most part you didn't change anything
  19. alldodge

    Starting outside of boat, on stand

    Depends on which manual, some 3/4 some 1
  20. alldodge

    Mercruiser 233 Overheating--Out of Ideas

    Thanks, inboard 351 Are the hoses routed as in the pic? Note the ports on top, front of motor go to elbows Next is there 2 gaskets and 1 plate separating the elbow from the manifold
Top