Search results

  1. alldodge

    Limited Power on Mercruiser 3.0LX Alpha

    Set at 1 BTDC
  2. alldodge

    Limited Power on Mercruiser 3.0LX Alpha

    If it would backfire at higher rpms then this would mean its running out of fuel. With it not doing that then this would not be the issue. If the filter was staying full then the pump could be weak or there would be a restriction. If plugs are still carbon and/or wet then the carb needs...
  3. alldodge

    Limited Power on Mercruiser 3.0LX Alpha

    Being an LX it would have a carb (2 or 4bbl). Could use a serial number so we know the configuration Need to check fuel pressure, should be 3 to 7 psi from idle to WOT Check the fuel tank antisiphon valve Your not getting timing advance or not enough fuel Have you heard any backfiring ? Is...
  4. alldodge

    Winterizing Force Outboard After Being Shrink Wrapped

    I'm not an outboard expert, but I also have never heard someone having to AF one, nor even anything online saying to do it. For water to break things, it has to be contained enough to there is not enough room to expand. Not seeing what happened to your old one, I'm unable to say Hope an OB...
  5. alldodge

    Winterizing Force Outboard After Being Shrink Wrapped

    There is no need to pump antifreeze into an outboard, it just drains back out
  6. alldodge

    Electric Fuel Tank Solenoid

    Want to add a fuel tank solenoid valve. To meet USCG requirements it must have a manual override. Parker use to make one (no longer) but it only have a 5/16 port (I need 3/8) and was used a lot on Searay's. Found a place in the UK that makes one, but does not list USCG cert (and why would...
  7. alldodge

    1989 180/3.7LX 4 bbrl Mercruisers exhaust to head gasket

    You might be able to do it, but suggest drain and remove it. This way you can find out what caused the leak. Need to check flatness of head and exhaust
  8. alldodge

    Engine Alignment Almost There

    Since it was installed incorrectly at first, I would guess the coupler has developed a set. Have 2 options, change things so you can find the least resistance with this coupler, or replace it
  9. alldodge

    Newbie

    :welcome: aboard
  10. alldodge

    2005 VP 5.7 to 5.0 Engine Swap

    While the lower HP will reduce top end, where it will really be noticed is getting up and on plane. The 5.0 has less torque and that will be noticed on first throttle up. You could get a long block and swap all your stuff over to the new motor...
  11. alldodge

    how to remove prop shaft seal on a duoprop DPS-A ?

    If bearing does not need to be replaced, use a punch and hammer to remove seal. Drive it from inside out To install new, I've used standard bearing/seal tool...
  12. alldodge

    4.3 MPI Performance issue

    If your compression gauge is accurate then there is liquid in the cylinders because 185 is way to high Fuel pressure should be 43 psi at 1800 rpm With key ON, what are the fuel pressure, TPS, MAP, IAC and battery volt readings when cold? With key ON, does the fuel pressure drop off hold or...
  13. alldodge

    2005 VP 5.7 to 5.0 Engine Swap

    Sounds like in short you have access to a cheap 5.0 so want to go that route. The 14 pin motor has a newer PCM and the 10 pin is either a carb or older ECM Your boat harness can be changed to a 10 pin but we would need to know what the original motor and older motor are. Also think about, the...
  14. alldodge

    Carburetor choke not opening?

    The choke won't fully open until the throttle is opened a bit now and then. The idle stop screw rest against the cam. Open the throttle a slight bit and it should open further as the choke heats up
  15. alldodge

    Need help finding an upper yoke input shaft for bravo one

    There the same length but the U joints are different Measure the inside and the Reg Bravo will be a tad larger then 1.079, the X will be a tad larger then 1.329 or 1.218 (meaning s/n 0W1000001 and below and 0W1000001 and higher) Ask at OSO wanted section, someone probably has one
  16. alldodge

    How to get out deep mildew stains from Vinyl seats or grab handles or steering wheel?

    With bleach not working, it may not be mold. Might be the fabric under the vinyl Could look into vinyl paint to re coat it
  17. alldodge

    Fuel venting

    The vent line needs to be routed according to USCG specs. Note the loop up and should be by the fill
  18. alldodge

    Ford to Chevy Shiftplate Relocation

    Can it be mounted in either of these locations?
  19. alldodge

    U joint crossreference for new style GKN

    U - joints come apart and go together the same way, only difference is the location of the clips Did notice are stickies are not all there, hey @GA_Boater have you noticed?
  20. alldodge

    Water in gimbel bellows, engine overheating & alignment tool, things to check before installing new engine.

    Water in the drive bellows is either a bad bellows or not sealed on the ends Yes, get an alignment bar. Got mine off ebay, and use a guy with many sales Rotate the gimbal bearing with your fingers to see if its as smooth as silk. If its not, it needs replaced An over heated motor can do...
Top