Search results

  1. alldodge

    Stumped! Engine stall after start

    Oil pressure switch should be 805024 or 87-864252A01 (old and new numbers) Oil pressure sensor should be 815425T or 8M0068784 Your electrical parts can be found here https://www.mercruiserparts.com/bam/subassembly/31511/2694/60 Your motor is here...
  2. alldodge

    Shift Interrupter Switch Merc 120

    This is an inline 6 but wiring will be the same
  3. alldodge

    Knock after gimbal bearing and joints replaced

    Think you may have a bad alignment tool since its hard for the drive to go on. Dimensions should be With the drive off, place your fingers on the gimbal bearing and rotate it, does it feel smooth?
  4. alldodge

    Crazy noise I cant figue out

    Here is a list
  5. alldodge

    Crazy noise I cant figue out

    Don't have a motor serial number but being a 98 I'm assuming its a MEFI 3 ECM If that is the case you need a resistor 12V LED which can be had at places like radio shack. Find the DLC connector, then with it and a paper clip, turn key ON without starting and count the flashes
  6. alldodge

    Bennett Trim Repair And Auto Pro Install

    Just a bit more info waiting on something from Bennett before I do anything. In post 51 I wrote: So went down and took some pics of the location and showing it is not orientated horizontal nor inline with the keel as the latest online version of the manual states I have room to place it...
  7. alldodge

    Mercruiser carb rebuild but hard start and idle

    Sierra that's kind of funny but your measurements are off when compared to manual 15 A whole lot of difference between 9/16 and 3/8 What kit number did you use and what type of needle seat?
  8. alldodge

    mercruiser alignment

    With on of these, part number 91-863372 Slides over the alignment bar, this pic shows the motor is high. As it gets closer, the gap reduces and if off on one side the gap will show a bit larger
  9. alldodge

    Mercruiser 3.0 choke/ idle issues

    Marine carbs do not have fast idle cams, they just have a rotating choke cam which should move freely
  10. alldodge

    4.3L Alpha One runs 6 minutes on topped-off fuel filter only

    A wire should not be able to go thru it., its a spring a steel ball
  11. alldodge

    1973 mercruiser MR-1 888 without gimbal mounted limiter switch

    Think your biggest issue is finding parts for the old design. Don't know if you have a 1 or 2 solenoid trim system so here is both. Unless your doing a restore for 100% accuracy, might thing about replacing the system with new design
  12. alldodge

    Bravo 3 overheating gear failure

    The B3 drive is known to run hotter then any other drive. When the oil gets high the lubrication starts breaking down and can brake things, One of the things that are part of the X and XR drives are the top finned cap. Not sure but do think this style cap will fit on all the newer swept...
  13. alldodge

    Carbon Monoxide at helm

    If your boat is like the one in the pic, then its coming from the design of the boat. The wheel house is creating a low pressure area. This area causes fumes to be sucked back in toward the helm. The boat needs some windows in the front to allow more air to pass thru reducing the low pressure...
  14. alldodge

    Boat trailer winch placement advice.

    You always want the winch to be above the boats bow eye, so it will help lift the nose as it is being winched on. I would suggest removing the whole piece and just install one bow stop roller at the end. You could leave the piece and install a roller at the bottom, but your still going to have...
  15. alldodge

    Bennett Trim Repair And Auto Pro Install

    Hey Tabman I posted this on the Formula forum and someone read the new manual online and that manual is different then the one I installed to, and is also different then the one that came with my last system. Here is a pic of the manual and the last control I just removed. Now here is the...
  16. alldodge

    Bennett Trim Repair And Auto Pro Install

    Went out today and its more of the same. Think I need to take my Go Pro with me next time for a vid. If I push FAV1 after I'm on plane most the time the tabs retract and I start leaning a bit. If I continue on and start turning a bit it will start to adjust tabs but not much and will not...
  17. alldodge

    5.7 alpha one gen 1 shifting issues

    Yours isn't that old, not a Gen 2 but not that old and should have the regular setup. Use the shift cable and mark the cable in F/R and place the roller in the center of the notch when cable is in the center of movement
  18. alldodge

    Finally Its Pay Back Time - Yellow Jackets

    About 12 or so years ago, I'm in French Lick IN following my nephew on an old Korean war Army Mule across where natural gas pipe line crosses the country. The Mule is not fast, top speed maybe 20 mph. My nephew is riding some 4 wheeler but not going fast. He goes over a bump in the field and...
  19. alldodge

    Did Volvo use SAME wire harness for multiple motors; extra plugs everywhere???

    This is the GL-C and D This is GL-E If we go back to a GL-A then there are less sensors, but most work off the same alarm wire
  20. alldodge

    2007 4.3L TKS Mercruiser starts and runs then dies after about 30 minutes.

    Thanks for double checking me, and I did look at the V* model, and should have been manual 32 (start with S/N 0M322781), but the torque specs are the same In post 1 you said it was a 2007 motor, an by looking at your intake, it appears to be aluminum. Manual 25 is 1998 to about 2000 (see S/N...
Top