Search results

  1. alldodge

    Throttle screw

    What carb do you have? If you don't know take a pic of the whole thing If its a Merc carb like the one below, as BT mentioned the 3 screws are loosened to adjust
  2. alldodge

    Logistics

    With all the problems folks are dealing with Harvey, all the very well intentioned people during what ever they can to help is so great to see and hear. The issue I see is the lack of logistics. Everyone is getting a truck load or more of stuff and heading down to Texas and hope also...
  3. alldodge

    Volvo Penta wiring HELP PLEASE!!!!

    Found this one some time ago and have it listed as the 4.3 GXI so it should work for the fuel pump. The pump wiring are the same for most the EFI models.
  4. alldodge

    Electric Crown Head issue

    You probably need to replace some hose, this is for foul oders seen on page 5 http://www.fondriest.com/pdf/Raritan_Crown_Head_Hi_Boy_Owners_Manual.pdf
  5. alldodge

    TKS Module Wiring

    Looks like Power Point didn't do to bad
  6. alldodge

    Throttle screw

    It might be bent but could also be just an optical illusion. The coke should move freely and when cold as the throttle is moved it should close. Move the throttle and see if the choke moves easy with your finger. If it does move freely but does not close when cold the choke pot needs to be...
  7. alldodge

    Throttle screw

    The closer of the choke plate is closed by the choke spring on the other side of the carb. The throttle control and idle cam (not really a cam on a boat carb). The two pieces come together at the top of the carb and are free to move independently. The choke is stopped by a tab which is also...
  8. alldodge

    Fuses

    Either inline or a multi holder link this one http://www.ebay.com/itm/Waterproof-marine-Sealed-fuse-holder-4-fuses-120-amp-kit-USA-made-/291076954623 Remove the fuse and splice in some wires coming out
  9. alldodge

    Help with Kohler 7.3E Generator

    My manual shows it to be connector J3
  10. alldodge

    1988 Merc 5.7L 350mag - Powering steering shaking the boat on moderate turns @ dock.

    Check to see if the slot on the tube is vertical (d) and nut (c) is tight
  11. alldodge

    2001 bass tracker Warning alarm problem

    I'm finding the serial number showing up as a 4 stroke EFI, but see no 2 stroker. In any case this is from the 4 stroke manual for continuous beep
  12. alldodge

    5.0L EFI Question

    Maybe, depends on how it was connected. Noid lights are LED's and have a + and - side. In any case, the Pink wires should have a constant 12V when key is ON.
  13. alldodge

    5.0L EFI Question

    The motors use the same Delphi ECU as the GM truck/autos but they are not programed the same. You cannot put one off a truck and have it work on the boat. Its very unusual for both ECU to do the same thing. They both supply spark but have no ground pulses going to the injectors. There is 12V...
  14. alldodge

    Brand new trim sensors ... how to set em?

    It has nothing to do with a ground. The limit stops the limit switch to stop working. This is done so you don't trim up to high when running. Note the Blue/White and Purple/White connections
  15. alldodge

    2013 350 MAG overheating (again)

    From your pic I'm seeing the thermostat for the Single point drain. In the link see item 20 (Tee) which is used to drain water out for winterization. The Tee has a bushing installed in the port going down which helps restricts water flow going up. This is done to help keep the engine a...
  16. alldodge

    Original Poster

    Don't want to add to admins troubles but if it would be easy I would sure like the OP of a thread to show up. Would sure help me to keep from getting off topic by another asking a question
  17. alldodge

    Single continuous guardian tone on 2006 mercury optimax

    Unable to find your motor on boat info but here is one which is close. Since it starts when you come to idle I would look at the water pressure first Item 3 is water pressure and item 5 is overheat http://boatinfo.no/lib/mercury/manuals/150efi-175efi-200efi.html#/32
  18. alldodge

    Winterization procedure for my engine?

    Items 9 and 11 are for the Bravo drive only. There is the 2 block plugs
  19. alldodge

    Winterization procedure for my engine?

    More stuff Or if you have something different
  20. alldodge

    Winterization procedure for my engine?

    Being that model you may have the Gen 7 pump, and if so there are 2 plugs on the pump. http://www.mercruiserparts.com/bam/subassembly/31493/12833/210 This is pics from the manual .
Top