Search results

  1. alldodge

    serpentine belt not turning

    Your right, the impeller has a set where it has been rotating clockwise and now it is being rotated counter clockwise. Also see what might be a crack. Either way looks like it needs to be replaced
  2. alldodge

    serpentine belt not turning

    Edit yes you listed your serial number so you have a 1998 engin Is your belt on correctly, you have the mando alternator
  3. alldodge

    B3 anode connection

    Picked up a prop shaft anode for my Bravo 3 years ago. It came in with a cone nut, hex screw and aluminum anode. Never did install it because after putting the rear prop on I only had 2 to 3 threads left. The new cone nut is not tapered to the degree the original nut is. Looking back the B3...
  4. alldodge

    Formula 27PC Complete Power plant rebuild

    Called and emailed Purosil and discussed. Larry Scott said he will get his engineers on it and give me a call back. Also called eddie marine and asked them. EMI indicated my current setup will not work and I should have bought there 3+ system which also dropped back down after the manifolds. The...
  5. alldodge

    Problems aligning my inboard engine

    The comments I made above was in reference to an inboard engine as your title listed. If the transom is flat, the bell housing and transom plate and assembly are not bent and assembled correctly, there is no way for the engine to be to the right/left. Hoist the engine up from the thermostat...
  6. alldodge

    Boy this one really has me stumped!

    I have a generac 5K but doesn't have the digital inverter. I found this on jackssmallengine, hope it helps some
  7. alldodge

    1989 carbed 454 temp issue

    You or someone must have changed them out. The old style for your year is in the link below and it has feeds for both manifolds and elbows. The Tee/valve item in lower left corner, it also has check balls. If the balls have been removed there is no restriction so water will flow out to the...
  8. alldodge

    troubleshooting thunderbolt V issue

    Here is the TB-V troubleshooting guide
  9. alldodge

    4.3 MPI MAP/MAT problem?

    Reading though the 555 manual No 36 you fuel pressure is good enough to start. Pressure should be above 35 psi and can drop but does not drop to 0. Check for spark and if that is good, next do a compression test. Have you tried swapping the Main power relay with the fuel pump relay? Check...
  10. alldodge

    BELLOW HEADACHE

    :welcome: to iboats Don't know what engine you have but my guess is you have a bad Y-pipe. If this is a V8 or V6 you have a Y-pipe, if this is a 4 or inline 6 cyl you have a single exhaust pipe. Pics below are similar and not necessarily what you have. If you provide a year or engine serial...
  11. alldodge

    Dual Ignitron System Thunderbolt IV & MSD6 AL need advice

    Don't think this will work. Your powering both TB4 and MSD but only plan on using one of them. The amps will be powered and don't know if the signal coming from the distributer will have an issue since it is connected to both amps. There will be an impedance difference and it is unknown if...
  12. alldodge

    1997 chaparal 1930ss 5.7 how do i know if i have thunderbolt ignition?

    You have a TB-V distributer
  13. alldodge

    Boat Actively Sinking - Need help with leak - Pics Attached

    Without a working bilge pump you were rolling the dice, so it was just a matter of time from lack of maintenance
  14. alldodge

    95 Rinker with Outdrive issues

    My rinker has the Commander 3000 control and it is located in the lower right corner of the throttle control. The pic below shows some of the different locations
  15. alldodge

    Formula 27PC Complete Power plant rebuild

    This is what I need the hose to do, would be an S bend, soft wall would kink. I sent the pic below to CMI for their comment. Well also call the folks in Scotts link tomorrow
  16. alldodge

    2000 454 MERCRUISER W/BRAVO 3 SHIFTING PROBLEMS

    DON'T KNOW WHY YOUR SHOUTING, we can read fairly well. To do a bravo adjustment see below.
  17. alldodge

    Formula 27PC Complete Power plant rebuild

    I need to find out about this black cloud that is following me around. Checked the gear lube it was ok, then put the drive on and the props. A little later I see lube under the drive. Pull the props and it's the inner shaft seal leaking. Sure looks like they didn't pressure test it before...
  18. alldodge

    Mercruiser 3L Fuel Delivery from fuel tank

    We are unable to see what your seeing so checking if it is installed correctly is just a question. Your model year can also have one of two different fuel pumps and one is installed up, the other down
  19. alldodge

    Formula 27PC Complete Power plant rebuild

    Gave it a quick between the bunk paint job today, plan to jack it up off the trailer at the end of the season and do it right for next season. Installed the turns downs and readjusted the engine mounts for a better alignment. Having of time waiting for the hose I find myself tweaking things...
  20. alldodge

    Ignition Switch

    A is assessorial and S is starter solenoid M for magneto and one goes to ground the other goes to the magneto
Top