Search results

  1. R

    1967 6hp Johnson rebuilt - running on one cylinder

    It will run just fine with those compression numbers.-----It is a fishing motor and not a Formula 1 motor.
  2. R

    1959 35hp RDS-21 Factory options

    ????----Why so puzzled.----You need a tiller handle off a 28 / 33 / 40 HP used from about 1960 to the 1970's.----Walk over I might be able to find one !!-----All easy.------And no the ones of the 22 cubic inch 18 / 20 / 25 HP won't fit.----All easy.
  3. R

    Tork

    A 1979 flywheel nut 115 HP is torqued to 102.5 FT-LBS
  4. R

    1971 18HP Evinrude Fastwin

    You can make a proper spark test device.------Take 2 or 4 pieces of wire ( even speaker wire )---Glue them on a piece of plywood or cardboard with 1/4" gap between them.----Stick one end in plug boot and clip other end to the block.----With 4 pieces of wire you cold test both ignition systems at...
  5. R

    Lube control cables

    Disconnect them at the motor.-----Operate the control box.-----Is it smooth.----And the motor must be running or propshaft must be turned when shifting your motor.
  6. R

    Lube control cables

    These factory cables are normally sealed and require no attention.-----Just curious why you ask the question.
  7. R

    Floats OFF on Walboro Carbs on a 86' 50 hp Mariner?

    Open low speed mixture screws 1/8th turn ( repeat if needed after testing ) and see if the hesitation magically goes away.
  8. R

    shifting issue with 1999 150 johnson

    Model # of your motor ?-----It may shift with cables removed.---And yes you will see the prop turning.-----But how would you determine / know that the clutch dog is fully locked into forward gear ????---So take the lower unit off and check / set the shift rod height.-----Make sure you use...
  9. R

    1971 18HP Evinrude Fastwin

    The term----" seemed to be getting spark "------Means nothing here.----Does spark jump a gap of 1/4" or better on a test device ???----That level of performance is required for easy 1 or 2 pull starting !!
  10. R

    shifting issue with 1999 150 johnson

    Has anyone been operating / shifting this motor with motor not running ??-----Have you checked the shift rod height ??-----In my opinion some of these lower units are not as robust as earlier versions.-----Just did a 97 model 150 gearcase.-----Two teeth broken on pinion gear.-----What a mess...
  11. R

    1953 Evinrude 15hp 15012 water pump question

    visit------nymarine-----To find matched colors.
  12. R

    Considering moving and changing my type of boat(ing) and want opinions

    Go to your local marina and see what style of boat ventures out on the rough days.----See / ask how long they stay out.
  13. R

    Need the Prop Gurus!

    The decals on this 1977 motor say 115 HP.------Step #1 is to determine if motor is still producing that power.-----Then you can experiment with a tachometer to find correct RPM range on the boat.
  14. R

    What year 85 HP Johnson

    Take water pump apart FIRST.----Post pictures.------Pictures of water pump parts and impeller drive key.----Pictures of shift linkages on front of block.---All easy.
  15. R

    89 Johnson 60hp won't start

    Dealer / factory part are only a few coins more.-----Support your local dealer while you still have one.
  16. R

    What year 85 HP Johnson

    The motor is a 1977 model.------Based on ignition parts and paint colour.----The 1976 and earlier models were GREEN .---So there.
  17. R

    89 Johnson 60hp won't start

    Get the primer repair kit.
  18. R

    1958 Fastwin Not Getting Fuel

    There is no EXHAUST anywhere near the fitting where you plug in the fuel connecter.----The motor pumps PRESSURE into the fuel tank.---Study how this simple system works.----Fixing it will then be easier !
  19. R

    What year 85 HP Johnson

    Hopefully they swapped some other parts too.----Powerhead gasket to exhaust adapter is not the same for these 2 models.
  20. R

    1967 6hp Johnson rebuilt - running on one cylinder

    Not easy for a novice ---Sorry.
Top