Search results

  1. Scott Danforth

    7.4L Impeller replacement attempt

    bravoitis?
  2. Scott Danforth

    Editing video

    I use handbrake to cut down and truncate videos. its free. I also use it to take video captures from CAD and condense them down to a format that can be emailed.
  3. Scott Danforth

    New engine - No Fire (Volcruiser)

    you did verify that the engine was at TDC on #1 before you try to install the distributor, correct? if your engine is a throttle body system, the fuel pressure is either 1 bar (15psi) or a 2-bar system (30 psi). if it is MPI, its a 3-bar system (45 psi) without enough pressure, you have a...
  4. Scott Danforth

    Primary and Secondary Imbalance - Alfadan Outboard Motor ?

    the merc 12 cylinder is a variation of an LS motor (a departure from their small displacement supercharged outboard architecture). so getting 600 hp out of their V12 was an easy feat, especially at 7.6 liters. the Alfadan is 8.4 liters and 4 cylinders. that is 2.1 liters per cylinder. about...
  5. Scott Danforth

    1995 OMC 5.0L IO starting procedure? Stalls when going into gear

    shift cable - check the ESA module you can adjust the neutral safety switch
  6. Scott Danforth

    Tube/Pipe for Routing Fuel Fill Line and Vent

    pvc with long-sweep elbows
  7. Scott Danforth

    Bow seat installation.

    what is below the deck in the bow? in addition to the plate, you may want to have a column run down to the keel unless there is a shear panel in the bow area that runs from keel to deck
  8. Scott Danforth

    Aluminum risers

    Either stick with cast iron, Or switch to stainless There is no good "low cost" option
  9. Scott Danforth

    Bow seat installation.

    What size stub? 3/4" is for 200# or less 2-3/8" is for under 400# 4" is for over 400" How did you reinforce the deck?
  10. Scott Danforth

    Reverse issue

    You have a new boat. You have warranty, call the dealer
  11. Scott Danforth

    New engine - No Fire (Volcruiser)

    Please explain what you did here several different ways... Stabbing a dizzy and setting timing is fairly easy
  12. Scott Danforth

    2003 crownline. 4.3l vortec. Help please.

    GM makes the motor, volvo bolted on marine bits Get a complete motor from Michigan motorz, edelbrock makes a marine intake
  13. Scott Danforth

    Aluminum risers

    Great on fresh water if you need to loose weight and keep on top of your maintenance. Not salt water friendly
  14. Scott Danforth

    1985 Bayliner capri cuddy 18'

    most likely attwood vents. look at the attwood catalog those parts are generic
  15. Scott Danforth

    1980 Sea Ray Sundancer Battery problem

    you will want to either take moisture readings or to test drills. 80's SeaRays were not the highest build quality
  16. Scott Danforth

    Velvo penta does on water

    this is the volvo specific muff. https://www.iboats.com/shop/seasense-volvo-penta-boat-motor-flusher.html
  17. Scott Danforth

    1985 Bayliner capri cuddy 18'

    The interior bits you will have to make yourself or hire an upholstery shop to make them You can get blowers from any marine store More importantly, how is the stringers, transom and floor
  18. Scott Danforth

    Water leak through haul

    You have to pull the drive to change bellows (recommended changing every 2- 3 years)
  19. Scott Danforth

    1980 Sea Ray Sundancer Battery problem

    Start chasing wires How is the transom and stringers?
  20. Scott Danforth

    Water leak through haul

    Pulling the drive and inspecting bellows is a yearly maintenance event Get in the bilge and look for the leak. Use mirrors, flashlight, and you cellphone camera to find the leak
View older results
Top