Search results

  1. T

    Hose leak at trim pump oil reservoir

    May have accumulated crud on flair. Sand or clean with 400 wet or dry sandpaper. Use sealer incase aluminum threads may have become cracked.
  2. T

    MC Oil Filter Kit Hoses Under or Over?

    I have remote oil filter kits on both my MC Chevy V8s/IOs. Unfortunately, I didn't take photo of hose routing when I removed starboard motor to rebuild transom. Port is pretty much ok. Filter mounting bracket appears vertical on starboard exhaust riser in some photos, but I cannot remember or...
  3. T

    Gimbal bearing. Is this normal?

    Make sure bearing holes line up with grease fitting on transom. Unless your grease fitting doesn't exist on transom. Then you may have incorrect bearing.
  4. T

    Need help identifying if exhaust elbow is good

    If they are salt used and over 4 years old, pitch them. If not, you should create a piece of flat metal and block off motor side, then pour acetone into the water side and check for leaks.
  5. T

    Gears with engine off

    It doesn't take much miss adjustment to not have fwd or reverse. Never like Alphas because there is not much room for error.
  6. T

    5.7 MPI Misfires Under Load

    AT NIGHT, check for leaking fire on plug wires. You will see it, if there is an issue.
  7. T

    5.7 alpha knock please listen

    sounds like sheet metal. Inspection plate loose?
  8. T

    Warning!

    a few years back, I purchased a rebuilt Quad-jet ( not a kit) from an American company. The company was listed on Ebay as American. It worked great.
  9. T

    Soak Bearings in Rust Remover?

    as others have said or implied.... replace bearing. You will sleep better.
  10. T

    Starter won’t engage flywheel

    Examine ring gear to see if teeth are still on flywheel. Trust me!
  11. T

    Engine was Full of Clear Fluid when I drained oil

    Pop one back in but I believe you are in for a motor replacement.
  12. T

    Outdrive Wont Go Up

    From time to time the rams should be rebuilt, depending on age and saltwater usage. They can and will get nasty inside. However, first jump solenoids. There is one for up and one for down on your pump motor. Examine to see if od raised and lowered. If not, you may have a bad pump. If you heard...
  13. T

    Mercruiser 4.3 oil gauge mystery

    Indeed, and there may be an ohm compatibility issue between sender and gauge. Been there!
  14. T

    Washdown Pickup Placement

    I was going to install one of these into plumbing to release too much pressure. It is a simple lawn sprinkler check valve. https://www.lowes.com/pd/AMERICAN-VALVE-PVC-Sch-40-1-2-in-Socket-PVC-In-line-Check-Valve/1000289419 Seacock installed. Sprinkler check valve has SS spring. I have used one...
  15. T

    Washdown Pickup Placement

    I was going to install (T in line) a simple lawn sprinkler check valve.
  16. T

    Washdown Pickup Placement

    that's exactly what I have, including "Blaster." Thx
  17. T

    Washdown Pickup Placement

    My boat can easily cruse at 30+ and I am afraid that the pressure would blow pump's seals and sink my boat, if gills faced bow.. If my old memory serves me correctly, years ago had a similar installation with gills facing stern and could not use pump while running on plane. I might install an...
  18. T

    Washdown Pickup Placement

    Not real sure what you mean by "parallel." U mean a thru hull pickup? Gills face bow or stern? I have a sea ****.
  19. T

    Washdown Pickup Placement

    I am installing a gilled bronze water pickup device to the stern of my boat, below water line and just below bottom of boat. Pump is inside and the pickup will be plumed along the outside of the stern and the plumbing will enter boat above the waterline. Should the gill slits face the water...
  20. T

    Starter starts something spinning in the back of engine only, nothing in the front.

    Pull starter and see if flywheel ring gear or starter teeth are in good shape. Hopefully just a bad starter set of teeth.
Top