Search results

  1. T

    1986 270 Amberjack Sea Ray

    I have looked aimlessly to find a windshield wiper pair (rubber and metal arm) to fit my ventage 1986. Wiper motors and studs are great as to the rest of the electrical. Any suggestions?
  2. T

    Gimbal bearing/bellows?

    Occam Razon: Easy to identify and plug with 5200. No brainier!
  3. T

    What is this?

    fine motor but why was moved from boat or maybe removed from truck in lieu of putting into boat. Run compression and oil checks to be sure. Keep in mind if your boat is carbureted, it is more laborious installing an EFI
  4. T

    Gimbal bearing/bellows?

    depending on condition of wooden transom and /or stringers, you may have flexing ROT. EASY TO test with drill and 3/8" drill bit. If crap or water comes out, you will be pissing away good money patching crap.
  5. T

    Ignition sensor help

    Phone aftermarket folks before u ruined it
  6. T

    Engine removal thoughts

    get a welding shop to build a steel A frame. You will need it AGAIN and can sleep well at night. Make sure wide enough to drive out boat. I lowered my 2 v8s into cockpit areal and covered but I had room.
  7. T

    ? About water in oil

    If saltwater block, expect inside block to look like this as well.... Cancer is cancer.
  8. T

    1987 CHRIS CRAFT AMEROSPORT 284

    YES! Just less iron to rust out.
  9. T

    1987 CHRIS CRAFT AMEROSPORT 284

    UR SOL! $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
  10. T

    1987 CHRIS CRAFT AMEROSPORT 284

    saltwater boat? replace motors and cooling risers and manifolds, now. Sound the transom for rot. If rot, expect a lot of money out of pocket, even if you can do work yourself. Trust me!
  11. T

    Gimbal bearing/bellows?

    Like Scott says and pray your transom is not rotten. Gimbal bearings and u-joints are cheap compared to replacing transom. Trust me!!!!!!!!!!!!!!!!!!!!
  12. T

    What is this?

    was it running? I never see a heat exchanger that small.
  13. T

    Mercruiser 5.7L warm start challenges

    Hook up a timing light and see if distributor is advancing as you rev motor. But, first check all battery connections!!!!!!!!!!!!!!!!!!!!!!!!!
  14. T

    Excess vertical play in intermediate shift shaft? Alpha1G1

    It may have worn out or possibly former owner dropped it or forgot to put it back. I had a Dodge truck transmission that would not downshift. Turns out that I left off a shifter washer that acted as a special spacer. Duh.....
  15. T

    What do I check next on overheating issue?

    Go buy a cheap inferred thermometer. Determine if the thermometer reading is close to your boat's temperature readings. That old of boat, I'd pull risers and rod them out.
  16. T

    5.7 Vortec dist, trying to seal the cap/rotor due to constant corrosion. Merc 350 Mag MPI Horizon.

    Build a drip tray similar to a gutter. You will have to figure out best place. Also, a piece of hard plastic across dist. and trim pump electrical will help
  17. T

    What's The Trick Mating Lower to Upper Drive??

    I feel your pain. I cannibalized a cheap scissors jack and welded extra parts on it. Unfortunately, when I sold my MC back in the late 90s, it went with the boat. Otherwise, I'd send photos.
  18. T

    Trim Cylinder Length

    Retract all the way in-Full Down.
  19. T

    Not good. Maybe

    On Chevy blocks there is a pipe threaded plug on each side of block under heads. You can use a mirror to see it. I believe it is 3/8" NPT. It will drain excessive water not dumped out by hoses.
Top