Search results

  1. S

    Yamaha lower unit disassembly

    please enlighten me to the location of the said "thrust washer"
  2. S

    rusted driveshaft repair

    There has been some discussion on how to do this. This is how I do it....
  3. S

    Outboard year by aluminum disk

    Here are the pics and control box
  4. S

    Outboard year by aluminum disk

    Hi Can anyone tell me what year a 60hp Evinrude with C7205076 on the block. The side tag is missing. Thanks
  5. S

    '84 Johnson 115 V4 lean sneeze?

    Also check closely for double firing. use a timing light on the offending cylinder and watch for ghosting or double images on the flywheel. Also....compression is not a "end all" of tests for engine condition. It is also possible that the offending cylinder has been damaged from fuel/oil...
  6. S

    Best hose clamps?

    Re: Best hose clamps? NAPA has "fuel injection hose clamps" that are great for fuel or oil lines.
  7. S

    Misfire on 3cyl with Quickstart and Slow pack repair

    There have been a few postings lately on pack repair. While this is not for everyone, some of us like to tinker. For all who are interested, It took 5 minutes to open pack. No damage to the pack, and no potting to remove found 6 cracked solder joints.....all easily repaired I...
  8. S

    1999 50hp 4-stroke EFI E50PL4SS WP valve

    Hi Gentlemen. I have a WP impellar that shrapnel-ed and I would like to try and find its pieces. Does anyone know where the water pressure valve resides? Thanks in advance.
  9. S

    lync and synce confusion , please help

    Re: lync and synce confusion , please help Whats wrong with the fuel pump?
  10. S

    Where does this piece go?

    Re: Where does this piece go? you are soo spoiled!
  11. S

    Where does this piece go?

    Re: Where does this piece go? That is your low idle speed adjustment. It mounts on the timer. You may have to remove the flywheel to install it.
  12. S

    Vapor separator question

    Hi This has been bugging me for years. Has anyone ever seen a schematic diagram of the plumbing of a vapor separator? How about a good operation description of the fuel bracket assembly.
  13. S

    crossflow crankshaft thread sizes.

    Re: crossflow crankshaft thread sizes. Hi Frank Yes you have to set your gear box to 14 threads per inch. Then engage the saddle until it near the chuck. Stop the lathe when its close. Never disengage the feed screw once you start. Insert the tap in the turret and mesh with the threads(as in...
  14. S

    Lower Unit Removal

    Re: Lower Unit Removal you have to remove the linkage. (you should have the manual)
  15. S

    crossflow crankshaft thread sizes.

    Re: crossflow crankshaft thread sizes. daselbee - Thanks, that takes care of the metric possibility. Chinewalker - Boy I sure hope its not a Yamaha. The only differences I could see are the rod journals are hollow, and the bottom seal ridge is approx. 1/4" longer. I hope its just newer than my...
  16. S

    crossflow crankshaft thread sizes.

    Hi Does anyone know if crossflow v-4 crankshafts all use the same thread size for the flywheel nut? I purchased a used unknown year crank and the threads seem .006 larger OD than the original and my nut won't fit. Thanks
  17. S

    crossflow crankshafts

    Hi Can anyone tell me if a crank from a J115TLCOS will fit a j140TLCIM? Thanks
  18. S

    Am I leaking gear oil?

    Re: Am I leaking gear oil? check if the housing is split or the retainer nut is out of place. I don't like the space shown here
  19. S

    How to wire an overheat buzzer on 1977 35hp (35e77c)

    Re: How to wire an overheat buzzer on 1977 35hp (35e77c) http://www.senasys.com
  20. S

    How to wire an overheat buzzer on 1977 35hp (35e77c)

    Re: How to wire an overheat buzzer on 1977 35hp (35e77c) you can buy a cheap thermo switch and connect it in series with a buzzer.
Top