Search results

  1. S

    Flywheel and Stator removal

    Re: Flywheel and Stator removal You can make your own as I did. I was pissed when I found one later on ebay for $20 !!!
  2. S

    Yamaha 150 ProV Over heat issue..HELP

    Re: Yamaha 150 ProV Over heat issue..HELP check inside the w.pump housing and see if there is any melted "housing plastic" obstructing the outlet. If so, it means the stainless cup has likely moved up into the housing and blocked off the bleed hole....= poor pumping
  3. S

    Still Need Help - Water Pressure Gauge Not Working Yamaha 2003 115 HP

    Re: Still Need Help - Water Pressure Gauge Not Working Yamaha 2003 115 HP part 18 (pressure regulator valve)
  4. S

    1980 140 Spor Evinrude Warm-up lever cable question

    Re: 1980 140 Spor Evinrude Warm-up lever cable question its likely that your fast idle lever and mating linkage are worn as shown below. You can try to locate new ones or drill in and install roll pins as I have done...
  5. S

    1965 Johnsn Seahorse 33HP (Paint Codes)

    Re: 1965 Johnsn Seahorse 33HP (Paint Codes) try these:
  6. S

    Honda 50 hp carburetor hose configuration

    Re: Honda 50 hp carburetor hose configuration Does this help?
  7. S

    making a copper fire ring on head gasket

    Re: making a copper fire ring on head gasket if your gasket looks like this....they are still available for purchase
  8. S

    1996 mercury 150 xr2

    Re: 1996 mercury 150 xr2
  9. S

    1988 BlackMax XR4 150hp float

    Hi Gents The manual shows to adjust float level so the float protrudes 1/16" out of bowl when inverted. The floats I have are plastic and have a hump on their topside. Would I measure to the highest point of the hump, or to the outer edge of the float? Thanks Picture available if needed.
  10. S

    Max timing

    Hi Gents Can anyone tell me the max timing on a 1987 Yamaha V150 Pro150H Thanks
  11. S

    DVA Voltage specs needed

    Re: DVA Voltage specs needed
  12. S

    Help with Link n' sync, please

    Hi Can anyone tell me how to properly adjust this linkage? I can't find it in my generic manual. Its on a 1996 Johnson 60hp. This adjustment controls the start of the advance curve. Thanx in advance.
  13. S

    Part Number Help Please.

    Hi Gentlemen. Can anyone tell me the part number for a 60 C (140 F) thermostat for a 2005 115hp Merc 4-stroke EFI. S# 1E000407 Thanks Randal
  14. S

    Manual TNT release only allows down motion....

    Hi Does anyone know of a reason why a 1995 50hp Evinrude TnT manual release will allow the motor to drop, but not allow it to be lifted up by hand? Thanks
  15. S

    Fuel hose-I need to be set straight!

    Hi Gents Can anyone tell me whats going on with fuel hose for outboards. I need to be set straight. The local Napa's and B2B's have hose alright, but its not rated for "oil mixed fuel". OMC isn't listing hose for half of their outboards I've checked. What is everyone using? Is the yellow plastic...
  16. S

    pinion depth measurement

    Hi Has anyone ever seen the dimensions for the OMC pinion depth tools posted anywhere? I can't seem to find them anywhere. Why are they so rare? Thanks in advance.
  17. S

    forward bearing housing "roller bearing"

    Hi Has anyone replaced the forward bearing housing roller bearing equipped with a DD-52404 torrington? The bearing is not sold separately by the OEM. Thanks
  18. S

    Flat rate overhaul time for V-4 crossflow

    HI Can anyone tell me the flat rate time for a complete engine overhaul including pistons, carbs and waterpump. (1993 115hp evinrude) Thanks in advance
  19. S

    S.L.O.W. which models?

    Hi Gents Can anyone tell me which models are equipped S.L.O.W. Thanks
  20. S

    Z9000 Eagle Depth Finder

    Hi all I have a Z9000 finder that has given me good service. Recently it has developed a few spots on the screen. Does anyone know how to clear them? They remain constant with power on or off. Thanks
Top