Search results

  1. M

    Yamaha v4 prop shaft carrier nut torque

    Replacing prop seals and bearing carrier o ring. Got the carrier out but wanted advice on using antiseize on the big carrier retaining nut threads. Good or bad idea? Also need the torque spec for that big retaining ring nut. Thanks 2001 yamaha 130 hp v4 2 stroke
  2. M

    Rigging preference

    Just checking which is preferred bundling the excess harness lengths at the helm under the center console or at the stern before it passes through to the outboard? Some of my harnesses have a lot of extra length. For what it's worth it's a 1997 wellcraft 190ccf with 2001 yamaha 130hp v4 2...
  3. M

    Yamaha 130 fuel connector

    Rigging a 2001 130 v4 2 stroke. Looks like yamaha wants a fuel hose from the primer all the way up to the filter with no quick disconnect coupler. Was thinking about adding one but all the Rigging coming out of the motor well is going to be inside a Rigging tube with the exception of the fuel...
  4. M

    Wellcraft 190 ccf engine install

    I still had a concern because the rule of thumb was 1 inch up for every 12 inches of setback but I only have about 7 inches of setback. And I was hoping to get info from owners of the same boat. Sorry
  5. M

    Wellcraft 190 ccf engine install

    my 1997 190 ccf is about to get a 2001 yamaha 130 2 stroke installed. There is no room in the transom area for the oil tank. I think I have to put it on the floor of my center console. I will run a remote oil filler plate to the side of the console around where the 190 ccf decal is. Seem like a...
  6. M

    Wellcraft 190 ccf engine install

    getting ready to install a 2001 yamaha 130 v4 2 stroke on my 190 ccf. original engine (johnson 115) was installed so that cavitation plate was about 1 inch from the bottom of the boat (boat uses a stepped transom with about 7 inches setback). Do you guys advise just mounting the yamaha so that...
  7. M

    Yamaha key switch mount horizontal

    I just found them. Bought just the bezel for key and the single kill switch part. Thanks
  8. M

    Yamaha key switch mount horizontal

    I like that. Where did you find those? Have any part numbers?
  9. M

    Yamaha key switch mount horizontal

    Good idea. 👍
  10. M

    Yamaha key switch mount horizontal

    I have to mount my key switch panel sideways for my 2001 130 v4 2 stroke due to space issues. This puts the key switch in a position that makes it look like it's on even when off. I tried rotating the switch 180 degrees but same thing. Due to the flats on the switch body and panel. Any way to...
  11. M

    Mounting bolt tab?

    Getting ready to take the johnson 115 off my 97 wellcraft 190ccf center console. Lower bolts have some kind of tab over the head of the bolts. What is the purpose of these?
  12. M

    Yamaha 130 hp 20 " shaft mounting height

    Because I haven't beaten this to death I measured my actual setback at 7 inches so I guess I should be 1 inch up from the bottom of the boat?
  13. M

    Yamaha 2 stroke oil hose

    I'm thinking it's a good idea to change the under cowling fuel hoses. Instead of buying all the individual hoses do you know what size that fuel hose is? Might buy it in bulk instead. My gas hoses feel pretty hard to the touch is the reason I'm thinking of replacing them. Thanks
  14. M

    Yamaha 2 stroke oil hose

    I see it now in the parts diagram. Thanks
  15. M

    Yamaha 2 stroke oil hose

    Thanks I got the new oil hose already. So the rubber hose doesn't run all the way to the under cowling tank?
  16. M

    Yamaha 2 stroke oil hose

    I have a new to me 2001 yamaha 130 v4 2 stroke. Previous owner cut the oil hose about 2 feet hanging outside the motor. Does the rubber oil hose from the remote mounted tank run all the way under the hood to the main tank or am I supposed to have a different material hose under hood? If so I...
  17. M

    Yamaha rigging

    I have a mechanical steering cable. Should I drill a hole and run another grommet for just the motor stuff?
  18. M

    Yamaha rigging

    What does that mean?
  19. M

    Yamaha rigging

    Anyone have any ideas for a clean rigging install? Yamaha 130 v4 2 stroke. Was planning on using the rigging tube from Yamaha that fits into a corresponding motor well fitting. Only problem is my steering cable passes through this opening so not sure how to isolate the ribbed rigging tube from...
  20. M

    Yamaha 130 mounting height

    Shoot I'm sorry. I did have a case of altzheimers apparently. Sorry. Let me see if I can remove this
Top