Search results

  1. D

    97 Mercruiser 3.0LX will run/won't run

    Agree with Bondo here. You're putting the cart before the horse. Troubleshooting is a step by step process, you can't skip steps. You'll just end up wasting time and money thus increasing your frustration Yes, the shift interrupt switch can cause the ignition system to cut out, its part of the...
  2. D

    Motor won’t turn over

    You need to set idle speed and idle air adjustment. A carb rebuild isn't just plug n play
  3. D

    Motor won’t turn over

    At what rpm was it running? Should have the throttle advanced to about 1200 rpm on a cold motor til the choke starts to open
  4. D

    1996 SeaRay 215 Express Cruiser electrical issue

    Items mentioned here don't have a direct correlation with the charging system. Great they are all sound but even if any of the above mentioned components/systems had a failure it most likely would not affect the charging system Posted info earlier mentioned 15 volts running at alternator...
  5. D

    97 Mercruiser 3.0LX will run/won't run

    It's not acting up for the shop but they did confirm some important things for you Go boating with a spark tester and a helper, hope it acts up and report back your findings
  6. D

    1986 Mercruiser 470 water leak

    Yes. Some, if not all the bolts require sealant. Perfect seal, gasket sealer or permatex thread sealer
  7. D

    Needing help/ 4.3 mercusier

    A cracked block due to freeze damage, corrosion, etc can still run perfectly with good compression Best way to find out if the cooling system is sound would be to drain and pressure test it. Should hold 15 psi indefinitely, if not you need to locate the source of the leak
  8. D

    Ignition wire replacement

    Firing order is 1-3-4-2 May have to TDC #1 compression stroke to find #1 on the dist cap
  9. D

    97 Mercruiser 3.0LX will run/won't run

    You need to find out if you're losing spark or fuel upon shutdown/no start Pretty simple check, spark tester for ignition. Verification of fuel present at/in the carb. With the choke open you should see two steady streams of fuel when the throttle is advanced quickly
  10. D

    Started, died and wont restart

    Check spark Check fuel supply
  11. D

    Mercruiser and a kicker motor

    Couple options depending on the fuel tank. If there is another fitting in the tank for a pickup you could go that route. Otherwise install a shut off/directional valve in line between the tank and main engine fuel inlet
  12. D

    1993 Mercruiser 7.4 - Is my Problem Carb or Thunderbolt IV module

    And vacuum Will say if fuel pressure/vacuum tests good its way cheaper to rebuild a carburetor than update the entire ignition system
  13. D

    Alpha One gen 2 outdrive gasket pushing out

    Could be the o ring at the water passage moved outside the shouldered area upon drive install. Best to use a couple light dabs of bellows adhesive to hold it in place to avoid the o ring moving
  14. D

    1996 Sea Ray 215EC power steering belt and alternator belt

    Remove belt, take to auto parts store, have them match belt, install new belt
  15. D

    Motor won’t turn over

    Probably needs more throttle. Carbureted engines don't start as easily as efi equipped. Need to set the choke and advance the throttle before starting
  16. D

    Won’t idle 3.0 Mercruiser

    Head gasket, tuliped valves, detempered rings, etc... Guessing a valve job at a minimum, won't know for sure until you pull the head
  17. D

    Won’t idle 3.0 Mercruiser

    Agree with Kenny on compression test and locating impeller pieces Will add that 160 is too warm, most likely need a 143 degree thermostat. Verify actual temp with a laser thermometer
  18. D

    Question about installing new clutch/gear set in 1999 Bravo 3

    No, he's referencing the tool used to tighten the retaining ring for the input shaft bearing assy. The torque wrench attaches to the end of the tool which is roughly 12" long, therfore the amount of torque applied to the retaining ring with the tool using a standard torque wrench does not match...
  19. D

    Engine alignment ,just got the tool. Pics posted

    Right? And here I thought the engine didn't run well, or at least there's a vibration under load Something as simple as #5 and #7 plug leads being swapped can have the same effect you're describing. Especially on a twin setup with one engine 100% sound makes any slight issue with the other...
  20. D

    Engine alignment ,just got the tool. Pics posted

    Based on your posted findings I'd say the engine alignment isn't the cause of the vibration and is most likely okay. Being as the boat came from a shop and the issue arose right after the repair first item I'd check is the firing order along with condition/quality of tune up parts. Next would...
Top