Search results

  1. C

    2001 evinrude ficht

    depending on mdl# try disconnecting J1B on the EMM if fuse no longer blows at key ON it is likley a bad EMM here is blown fuse case on an ETEC 250... grandchild of FICHT using an EMM if not accessory caused somewhere on the purple from the switch and if the fuse no longer...
  2. C

    J115PX4STS Fluid Leaking From Top of Trim Cylinder Reservoir Tank

    checked with your dealer ?? ...there should be a reseal kit available
  3. C

    1948 Goodyear 5hp Seabee starter housing

    you can ask questions for free... membership fee is well worth the expense and you get technical support from experts. they also have a classified section to sell an buy.
  4. C

    2001 evinrude ficht

    post mdl# and year !!!! recent case like this came up recently be it ETEC or FICHT the EMM needs power to boot up and start the engine ... it then looks it self powers itself and no longer needs B+ from the key acc post to run. why does the battery blow.... well excess current...
  5. C

    FICHT video grandpa of ETECs

    just fyi...
  6. C

    2007 e-tec 250 lower mount corrosion

    well I looked at the parts listing and ETEC manual...it could be a lost cause but hey! faced with a 3K$ job try FB a heavy layer if you have to ... the stuff is prettty stong and... won't corrode anymore :)
  7. C

    2007 e-tec 250 lower mount corrosion

    https://www.etecownersgroup.com/post/lower-motor-mount-corrosion-10381738?highlight=mount%20corrosion&trail=15...
  8. C

    2007 e-tec 250 lower mount corrosion

    depending on how solid the rest is.... Call me cheap but.....if money is short and won't buy the parts you need and we are all faced with these decisions at one point...... you call always patch it up with the stronger automotive fiberglass imbedded car putty and noboby will tell...
  9. C

    Top speed??

    Brett from the french word "bretter" pronouced "brettay" ... which means hesitating .. not completing a task ... waisting time
  10. C

    tilt and trim rebuild 2000 50hp Johnson

    bottom line.. fill it and keep cyciling up and down as you keep refilling to top it off . this will purge any air in the syst. single ram T&T are used on some ETEC (like my 75)..from the manual :-)
  11. C

    Cowling gaskets for evinrude

    http://www.nymarine.ca/parts.htm
  12. C

    1978 70HP Evinrude Fuel Pump

    why not not just buy a new pump... some don't cost much more than gasket kits. Try a cheap one on Amazon ... I know it is not OEM (sacriledge) but it will get you going.
  13. C

    Finding information on my mysterious Evinrude 4hp...

    changing the impeller is routine maintenance on any OB and unless you know who put it in and when theimpeller should be replaced. not because it is currently bad but because it will turn bad at an unknown date in the future and odds are your engine will fry before you can even...
  14. C

    Finding information on my mysterious Evinrude 4hp...

    thanks for updat pics... yes lots of variables but same basic procedure drop GC pull pum housing save the key etc.....
  15. C

    tilt and trim rebuild 2000 50hp Johnson

    but I have cheated a few times :-)
  16. C

    Finding information on my mysterious Evinrude 4hp...

    the more modern engines evolved from oldies with their simpler designs .Modern capacitance discharge ignitions are simpler in design (less or no mechanical parts) but the mechanics have not drastically changed. to read up on oldies a cheap book to "learn" from is the Johnson...
  17. C

    tilt and trim rebuild 2000 50hp Johnson

    oem goes into millions of outboards ...for a good reason.
  18. C

    Finding information on my mysterious Evinrude 4hp...

    3- 4- 5 hp etc... all have the same basic structure if you plan to service small engines you need to get yourself manuals or seach utubes for your engine... make certain impeller blades will turn clockwise looking down at it when installed
  19. C

    Finding information on my mysterious Evinrude 4hp...

    don't loose the key pin !!
  20. C

    Finding information on my mysterious Evinrude 4hp...

    make certain the top vent is open while running and make certain the air holes are not crudded shut . before you tear into it (carb) try some evinrude engine cleaner in the fuel run it awhile it may clear up. some use/like seafoam some don't like it.
Top