Search results

  1. C

    9 1/2 Evinrude

    how is theengine performig ??? 9.5hp are not flaming draggons.
  2. C

    1973 Johnson 50hp need some advise please.

    if you have a camera peek inside the bad cyl. check for scoring etc...
  3. C

    1989 Evinrude 88SPL (E88MSLCER) PTT

    search utubes you may find something to assist in solving the problem and tool selection
  4. C

    2019 E-Tec 150 HP

    suggest you consult with the folks on the ETEC USER BOARD for commercial high output conter rotating engine select appropriate group if G2 model select G2 sub section https://www.etecownersgroup.com/categories
  5. C

    2019 E-Tec 150 HP

    mdl # ?
  6. C

    1975 9.9 sea horse

    http://www.leeroysramblings.com/OB%20carburetor_repairs.html lots of utubes on carbs...
  7. C

    2006 Evinrude 60 horse etec keeps blowing 10 amp fuse

  8. C

    6HP Evinrude Fisherman

    pull the carb ...clean all orifices blow all passages 6hp is a wonderful little engine should work great. lots of utubes to help you clean that carb...you may as well check under the flywheel check all electricals, replace condensers if never done clean the points etc...etc...
  9. C

    1989 Evinrude 88SPL (E88MSLCER) PTT

    had same symptoms on my 75 etec....the PTT likely needs a seal rebuild 6oz low on the oil indicates a leak
  10. C

    2006 Evinrude 60 horse etec keeps blowing 10 amp fuse

    the fused power only feeds the T&T relays with very little amp draw... removing the middle EMM connector J1B as been known to confirm a defective EMM .... (the fuse only stops blowing with all accessories still connected indicating that the amp draw is mainly the EMM . If recall correctly...
  11. C

    Vintage 9.5: Can you set points with a timing light?

    don't make it more complicated.... Remove the FW and just set points at .020 on the hight point of the cam lobe or get the pointy tool ..works great just... openning at the mark is more critical than the gap itself
  12. C

    9.5hp Johnson - what's this screw for?

    I have never seen a 9.5hp with that filter ... but the MQ10 1964 shows one. they must have kept the mold same for part 15 19 & 20 idle limiter molding btw for easy scren grabs use windows key - caps and S buttons
  13. C

    Vintage 9.5: Can you set points with a timing light?

  14. C

    2006 Evinrude 60 horse etec keeps blowing 10 amp fuse

    suggest you consult with the folks on the ETEC user board in the i2 section https://www.etecownersgroup.com/etec-i2-136482 the fuse feeds theT&T switches and the front key.. the key loops B+ back to the EMM on purple via J1B pin #10 ( middle EMM plug) ... saddly.... blowing fusues are...
  15. C

    1977 Evinrude 85hp - Oil Leaking from Air Silencer Cover

    on older engines the crankcase residual fuel-oil mix is simply purged out in the water or recirculated to the top of the engine by a side recirculation hose. They even have recirculation concept on modern E-TEC engines ! if you can't solve your problem and you are loosing sleep on it...
  16. C

    Help! Won’t start when hot.

    how is the impeller doing ???
  17. C

    Lower unit oil

    side issue here ... but some of you may recall $20/month phone bills.... and complaints against the main Telco for their " local service subsidizing" high long distance rates enough to break up AT&T in the 70's Today the whole family runs around with thousand dollar phones plus...
  18. C

    Unknown 55hp Johnson boat restoration

    well if you ever do another one here is a great book to restore old FB boats https://www.amazon.ca/Runabout-Renovation-Find-Fiberglass-Speedboat/dp/0071580085
  19. C

    Lower unit oil

    well if you dump it....... they will think you are rich .
  20. C

    Lower unit oil

    tell them to save it and reuse it !
Top