Search results

  1. C

    2-cycle gas

    lawnmower fuel ....
  2. C

    Johnson model J115FTLECS 115hp 2 stroke 2 cylinders not firing

    see diagram
  3. C

    Johnson model J115FTLECS 115hp 2 stroke 2 cylinders not firing

    FICHT .. pre ETECS likely fire their coils by grounding the ignition coils...... some model it seems actually feed current to the coils and the EMM breaking that current fires the coil due to the collapse of the primary magnetic field coil which induces the high voltage spike in the...
  4. C

    Why can't I find this part?

    if all else fails have you considered having one duplicated ...a local mill shop may be able to " turn " one on a lathe....the design seems simple enough. good project for a local trade school.
  5. C

    1967 evinrude 9.5

    did you adjust like this,... have you rotated the side ... idle knob to limit travel
  6. C

    Faulty starting solenoid

    selenoid are just magnets closing contacts to allow the high amps flow to the starter. some are activated by grounding some are activated by applying 12v generally... the magnet coil is extended to 2 small posts. one is either grounded by a modern computer like ETEC EMM or powered by...
  7. C

    18hp evinrude bad cough

    check compression recheck carb ... blow out ALL passages with carb cleaner incl. side channel to upper LS needle check under #25
  8. C

    200hp Evinrude FICHT No Spark

    tps value seems out of wack ... active faults tps is a voltage derived from a variable resistance. ON ETECS it gets 5v from the EMM and a return voltage around betwen 0.15- 4.925 v max value tells the EMM where the throttle plate(s) are positionned. recheck the TPS connections...
  9. C

    1977 johnson 6hp throttle cam question

    the cam is adjustable loosen the bolts under the mag plate. the other bolt is a pivot bolt. just tighten it after you do the one on the right side . set tiller to START and cam should just touch the cam follower and line up with the mark on the cam throttle plate should begin to...
  10. C

    1977 6 hp johnson waterpump

    PW is giberish for PH... power head vermitherm is new to me
  11. C

    1977 6 hp johnson waterpump

    remove the gearcase...backflush the PW with air compressor to see if air flows freely back out the water tube. try air pressure from the pee hole and thermostat have you try passing a mono line up the pee hole ? did you have any missing fins on the impeller when you replaced it ? did...
  12. C

    Johnson 15 hp fuel pump

    read ...read.... read .... and then do a few .......then it is easy see #41& 42 in Leroy's site http://www.leeroysramblings.com/Outboard%20Motor%20Related/OMC%20outboard%20related%20articles.html
  13. C

    1966 johnson 6hp condensers

    http://www.leeroysramblings.com/johnson_magneto.htm there you go
  14. C

    Can I bypass the solenoid yellow wire in 79 Evinrude outboard?

    wires usual break in bends....hold the key at START...while turning the engine left and right with the steering. another area of problem is connectors.. open any connector and clean the mating surfaces of wires (M&F) check fuses if any...... replace or test if ok ....... reseat.. ...
  15. C

    Best solvent to soak parts

    no such thing as a dollar store anymore... thet are 4$ stores :-)
  16. C

    1966 johnson 6hp condensers

    unless you can measure capacitors properly it is hard to tell when and how bad they fail.... barring an obvious short circuit giving you a constant low resistance value it hard to say how bad things are. they realy need to be tested with high voltages to detect leakage between the 2...
  17. C

    Best solvent to soak parts

    salt can go with boiling it in hot water ... calcium can be dissolved with plain vinigar ..(hotter the better) petroleum gunk can be dissolved with lacquer thinner and some folks just soak in Pinesol. ultrasonic cleaners help or dremmel wire brush
  18. C

    Water temp warning ?

    try this site where ETEC owners share problems ... https://www.etecownersgroup.com/?forum=136487
  19. C

    Evinrude yachtwin 3hp peeing question

    just in case try to torque all the bolts in case someboby was in there and did not close it up properly. it does get pretty hot under that plate because the 3hp exhaust plate is not water cooled like other ones on biggger engines see a 7.5 exhaust cover with the inside plate and...
  20. C

    33 hp

    close enough ?? https://maxrules.com/graphics/omc/wiring/1957-60_35-40.jpg what problem do you have ??
Top