Search results

  1. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    If it runs great and starts great injectors likely ok. compression likely ok also so you are missing fuel as the 3rdelement. do you recall when all this issue started? how are the filters ...new ..old... crudded . tank venting ok ? did you inspect the return filter #7 on...
  2. C

    Johnson 115 ocean pro running on one cylinder

    may as well check for sparks on the dead cyl.
  3. C

    hard to start when warm

    nobody could start my old Merc 500... all it needed was special TLC and started everytime ... ++ racerone comment
  4. C

    Durbans Johnsonator outboard motors .

    9 years later ??? this better work :-)
  5. C

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    The cross pin is hard to see in the photo supplied by OP but this seems to be a winning solution based on this parts picture
  6. C

    1980’s Evinrude - Temp Warning System?

    https://www.amazon.ca/MG-Chemicals-Silicone-Transfer-Compound/product-reviews/B005DNQWQU/ref=cm_cr_dp_d_show_all_btm?ie=UTF8&reviewerType=all_reviews good glue to mount alarms sensors metal over metal good excellent heat transfer
  7. C

    1980’s Evinrude - Temp Warning System?

    Mount & hook up a few of these on a piezzo buzzer ! chose 60 (140 F) or 70 C (158F ) normally open contacts will close when hot...
  8. C

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    cross pining it may work ???
  9. C

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    depending on actual shaft size ......tried drilling tapping and bolting it back in one piece ? welding seems possible with those wire feed welders
  10. C

    $50 150hp Gambling project (pics)

    Lebaneese proverb... Be generous willingly in life otherswise when you die all your precious belongings will be given away.. incl your boat. !!
  11. C

    2005 Evinrude ETEC 200 no start question

    you did reinstall and orient the magnets properly ?? ...sorry to ask ! check EMM LEDS conditions and compare to pages 127 -128 in the manual https://www.etecownersgroup.com/?forum=136483...
  12. C

    Intermittent water

  13. C

    E-Tec 60 HP.-

    is it not with the hose garden style flush port what year is the 60hp
  14. C

    1948 Evinrude 3.3hp carb

    yet...everything simple.. is complex and ends up in the garbage can because we can't fix anything anymore....:-( The toaster became complex when they moved up from the two door slice flippers :-)
  15. C

    My '55 5.5 outboard

    if you can wait a bit...not to bad a price free shipping pull your flywheel coils inside likely cracked...
  16. C

    My '55 5.5 outboard

    btw is the gc getting water ?? if not no need to mess with the GC do pressure test. if it holds pressure and vacum it is ok . just do the impeller carefull with the brittle carbon seal on top of the drive shaft . the book CHEAP OUTBOARDS is a good one and covers the 5.5hp...
  17. C

    40 hp evinrude (year unknown) selectric shift model. HELP setting points and timing!

    Lol so glad to find a forum with such great guys. you may want to visit the AOMCI web site for oldies maintenance... https://aomci.org/forums/forum/ask-a-member-d1/
  18. C

    My '55 5.5 outboard

    try IBOATS for parts or https://www.amazon.com/Sierra-International-18-7100-9-Marine-Ring/dp/B000LN4ILI/ref=sr_1_2?crid=1VJ2N5CQB5IN&keywords=sierra+18-7100&qid=1644181479&sprefix=sierra+18-7100%2Caps%2C83&sr=8-2
  19. C

    `97 Fast Strike 150 trim/tilt issue

    great news. thanks for feedback. relay contacs do oxidize and stick ON keep an eye on everything in case excessive current was carried on the T&T motor and damaged the relay contact surfaces. Everything will probably be fine with new relays
  20. C

    My '55 5.5 outboard

    oring liklely 0301877 best to get OEM orings ... see utubes on how to replace it it not familiar how to. identical size somewhat hard to find :-(
Top