Search results

  1. Grub54891

    1980 305 mercruiser inboard stalling at worse possible times

    Re: 1980 305 mercruiser inboard stalling at worse possible times You can add some tension to the interrupt switch by slightly stretching the spring behind this plate,you can get these springs new also,take it out,tweak it put it in and try it.
  2. Grub54891

    Shift shaft question

    Working on an 1983 mercruiser,alpha drive. Don't have the serial number in front of me but,the shift shaft that goes through the exhaust bellow is loose in the bushings. The bushings were replaced last year,and the shaft measures 3/8 all the way down. Did they change the diamater of the shaft at...
  3. Grub54891

    1948-1950 Flambeau

    Rescued from the scrap pile! I'll be fixing her up but where to get parts?
  4. Grub54891

    1948 flambeau

    Just acquired this! $20.00 It has compression,I have to check how much,but it feels good. And have to clean er up,check spark,and find an impeller. When I get her running,I'm going to paint it up like new,and have the decals made up. It's not even dented anywher. Grub
  5. Grub54891

    140 HP OMC Caburetor idle adjustment

    Re: 140 HP OMC Caburetor idle adjustment Ya took it apart,did you rebuild it? Sounds like ya didn't. It has to be clean inside,all components taken out,cleaned,wired out,air blown dry. Just adjusting the float makes thing's worse as now it's not in spec. Had a similar issue from a...
  6. Grub54891

    Volvo drive oil

    Neighbor has been using quicksilver hp drive oil in his outdrive for the last 3 years. Don't know the exact drive right now,but it's a duoprop. I know volvo recommends volvo oil only,but what could happen? Is their oil that much different? Grub
  7. Grub54891

    Bellows adhesive smoking?

    Re: Bellows adhesive smoking? Sometimes when them tubes sit around to long,they go bas/ingredients separate in the tube. It should be one color all the way through.get the real stuff! grub
  8. Grub54891

    Lower Unit (3) rubber boots broken...water coming in through back of boat?

    Re: Lower Unit (3) rubber boots broken...water coming in through back of boat? Bellows adhesive is not silicone,do not use silicone on any bellows. Use bellows adhesive!
  9. Grub54891

    Timing Info Needed for '85 140

    Re: Timing Info Needed for '85 140 You will want to get one of these to get at the bolt easier,
  10. Grub54891

    Realigning Pulley

    Re: Realigning Pulley When ya make shure the brackets and spacers are all ok,if it needs to be moved,you need this puller/installer. Any automotive parts store has the,some may rent ya one.
  11. Grub54891

    Trick To Removing Old Hose?

    Re: Trick To Removing Old Hose? Look up hose pick. They work well to get between the hose and fitting and not damage it. I've used the cheaper ones and end up bending,breaking them. My current one is a snap-on and is holding up well.
  12. Grub54891

    Impellers

    I have impellers all over the webpage,I use an I-pad,Is it me or......?
  13. Grub54891

    Newbie, Rebuilding 1976 Hammond Eldorado V1950

    Re: Newbie, Rebuilding 1976 Hammond Eldorado V1950 Looks as bad as my larson...... Just gelled the transom today!
  14. Grub54891

    Shore power breaker

    Hi, been looking to install a 30 amp breaker on my shore power line. Would like to put it in a weather resistant box in the cockpit area,just after the shore power inlet.I cant seem to find one that looks good,easily opened quality built. Any suggestions? Thanks in advance! Grub
  15. Grub54891

    bilge pump ideas

    Re: bilge pump ideas You may need to install one of these to gain access to install a pump
  16. Grub54891

    Holding tank

    Re: Holding tank There should be a fitting on the deck to hook up a pump out fitting. Most marinas have the proper fittings and pump by their fuel dock,usually charge a fee for doing it,but do it free if ya are buying fuel and supplies.
  17. Grub54891

    Access to Frost Plug 140

    Re: Access to Frost Plug 140 Sounds exactly like mine,1985 larson bowrider.140 mercruiser. All freeze plugs popped,replaced and runs like a champ. Only paid $200.00 for it,and the upper drive was blown. It came with a spare drive so that was an easy swap. New bellows,ext. in process of full...
  18. Grub54891

    Is it a good idea to use hardybacker for a floor in a boat???????

    Re: Is it a good idea to use hardybacker for a floor in a boat??????? Whats a hardyback? And laying a floor over a rotted floor is not a good idea!you will end up with this! Rotten transom to. Grub
  19. Grub54891

    I'm tired of PMS!!!

    Re: I'm tired of PMS!!! Supposed to get a foot tonight,dammmm.
  20. Grub54891

    What a relief

    Re: What a relief Still waiting.... Ya I have a couple more boats but I'm dealing with this.... To much snow and to much restoration...lol But I'll still be boating if the one isn't done!
View older results
Top