Search results

  1. C

    1968 6 HP Evinrude need help

    not up to >50 posts yet :) but it already wins the post/hp ratio :)
  2. C

    1968 6 HP Evinrude need help

    i hope the manual helps but... these are simple motors ...aside from problems with the innards the rest is just about everywhere on the net . check out Leroys subjects and you will find pretty much all you need http://www.leeroysramblings.com/OMC_6hp.htm...
  3. C

    1966 9.5 Evinrude won’t start.

    any chance plug wires are crossed ?? what is the history never worked or stopped suddenly ? anybody worked on it recently ? read Leroy'S on the 9.5hp carb MUST BE 100% clean The high speed jet is located in the float bowl which is located in the bottom 1/2 of the carburetor. It...
  4. C

    1968 6 HP Evinrude need help

    bad hobby if you do not want to spend $$$ .... try the AOMCI site classified ads search ebay for a 6802R or similar carb for your 6hp it will be cheapest smooth running 6hp you can buy for an extra 50$ compared to a buyng a recent model. LS needles are pointy real pointy to enter...
  5. C

    1968 6 HP Evinrude need help

    and the 6802R does not have a hole on the face plate for a HS needle...???
  6. C

    1968 6 HP Evinrude need help

    see carb picture of pointy LS needle and if you open up the LS drip chamber under the ugly cap you should see the needle protrude pass the wall's edge inside the chamber . so the question remains... where did the carb come from ?
  7. C

    1968 6 HP Evinrude need help

    6802R shows upas a 1968 6hp all right but that he carb is wrong.....or the name plate is wrong or switched IN fcat none of the 6hp J&E have HS needles..that I could find anyway. and that carb color/finish seems wrong also... the finish makes it seems much older than the rest of the...
  8. C

    1968 6 HP Evinrude need help

    OK lets clarify something again ....if or do you have a both LS and HS needles.... because looking at your 68 6hp carb you have no HS needle only the top pointy one which controls the LS idle circuite so you can not be closing a HS needle completely. the HS circuit is...
  9. C

    1968 6 HP Evinrude need help

    High is also not a problem when I close HS needle completely. seems odd....with no fuel bypassing the needle tip at the bottom of the HS nozzle the engine should stop...do you have the fat washer installed at the bottom. test your coils and don't throwing parts at it...unless maybe...
  10. C

    Small Flywheel Tool

    do you mean hold... as in while you unscrew the top bolt ?? I use a small 1/4 inch impact screw driver / socket to remove bolts on 3-10 hp engines and they work great . no need to "hold" the flywheel
  11. C

    68 Johnson 9.5

    basics are not always basic to all and that motor does not sound to bad. No expert but I have reworked several 9.5 & most had comp#s in high 60s to low 70s none were speed bombs . these low compression engines were made to facilitate fishing- casting with their flat heads and easy...
  12. C

    1984 70hp Johnson, won't stay running

    try pumping the fuel hose.... does choke open up properly linkages all ok ? carbs cleaned ..yes no ???
  13. C

    1984 70hp Johnson, won't stay running

    choke working... dirty carb(s) bad gas ....??
  14. C

    1976 Evinrude 6hp..only getting spark in one cylinder.

    test coil sparks with a screwdriver in the boot held close to the engine frame.. if OK ...... bad plug
  15. C

    1976 Evinrude 6hp..only getting spark in one cylinder.

    6hp is a great motor and points are also a good system why not reinstall the points clean / gap them properly condenser may be bad keep coil wire away from the cam lobe ! test secondaries... boot to frame 3-7 KOhms depending on coil make
  16. C

    68 Johnson 9.5

    try running with the cowl off.... if much better it may be breathing it's own exhaust due to a poor sealing skirt down below just above the water pump do a compression test and report back what you find. they are low compression engines but 65ps seems a minimum.
  17. C

    68 Johnson 9.5

    see pict. good luck it is only a 9.5 with typically low compression #s good trolling motor and keep that high speed nozzle 100% clean see Leroys http://www.leeroysramblings.com/OMC_9.5.htm
  18. C

    1963 Johnson QD-24B

    when recoiled the small arrow should be lined up with J ZONE for Johnson models
  19. C

    Value of Brand New never used 1978 Evinrude 55 HP 2Stroke outboard 55875?

    well if innards ok depending on a 43 year sleep over I would start at nothing under 5000$ and wait for nibbles. nice find !!
  20. C

    69 Evinrude 6Hp correct spark plugs

    I think j6 is a bit hotter than J4 and better for trolling
Top