Search results

  1. C

    Vintage Johnson dual line gas tank - fit Evinrude 5.5?

    my only issue I had with a 7.5hp & pressure tank is that a pin hole (rust) caused 5 gal to leak and fortunately got dump out the boat which was tilted back with the plug removed. the lawn suffered major..total destruction. I switched it to a pump and modern tank....my 75hp ETEC...
  2. C

    1958 Johnson prop question

    well it may be stuck if original you may need ti invest for a new one https://www.vintageoutboard.com/collections/johnson-evinrude-water-pumps-impellers-lower-units/products/303365-prop-nut-cap-rubber-johnson-evinrude-5-5-and-7-5hp
  3. C

    1963 Johnson QD 24 10hp revival questions

    https://www.duckworksmagazine.com/06/columns/max/index6.htm here is a similar motor being revived
  4. C

    1958 Evinrude 7.5hp 7524 Poor Idle

    great news thanks for your feedback
  5. C

    Starter solenoid wiring - 77 Evinrude 70hp

    great news thanks for the feedback :-)
  6. C

    1957 Evinrude 5.5

    remove the starter assembly (3 bolts) remove the small plate on top of the flywheel and look inside if coils are all cracked...time to get new ones...points etc... to refurbish this a a great hobby ( be carefull ...very addictive once you enjoy the outcome)
  7. C

    Intermittent Pee Stream 1986 9.9hp J10RCDB.

    I just did a 9.9 a few weeks ago....the pee hole was clogged near the exit and was easy to clean up. I did take the opportunity the change the whole pump kit.... easy job. kit a bit pricy but owner happy.
  8. C

    Starter solenoid wiring - 77 Evinrude 70hp

    page a18 for the diagram http://www.boatinfo.no/lib/evinrude/manuals/1973-1991johnsonevinrude.html#/394 close to the fat red +12 post (3 wires) looks like the adjacent small post needs to go to ground directly the other post is the control post from the key switch ...on the diagram if I...
  9. C

    Evinrude 1984 25hp not pumping water

    certain IBoats here will sell the parts you need as well as any dealership or web site you google you can find parts list and diagrams on the web manual http://www.boatinfo.no/lib/evinrude/manuals/1971-1989johnsonevinrude.html btw check gearcase oil for water intrusion (milky like or...
  10. C

    Plug wires

    tried iboats :-)
  11. C

    Power pack or stator???

    well you need expert info on this one or read the specs in the manual http://www.boatinfo.no/lib/evinrude/manuals/1992-2001johnsonevinrude.html#/0
  12. C

    Evinrude 4hp frozen solid

    if you have access to the drive shaft no need to drill just send down some juice to the upside down PH and wait then resoak after a few days I like clear silicone spays they are clear like water and seem to have better capilary qualities to enter stuck boltsand all. Snowblower...
  13. C

    Evinrude 4hp frozen solid

    if the shaft is stuck in the PH....I would drill a small 1/8 hole in line with the drive shaft just below the PH and spray in some PB blaster or similar product inside and let it drain down to the upside down PH you can plug the hole later with a touch paint . Dollar stores...
  14. C

    Power pack or stator???

    ?? it is late question is vague what amp circuits are u referring to ....?? what does your manual refer to in ddescribing ohms tolerances ??
  15. C

    Will it Freez

    if you have a small drain hole on the lower housing...make certain it drains
  16. C

    Evinrude 4hp frozen solid

    if you snap the bolt you may have nothing to grab and soaking won't help much then you will be into drilling and tapping 😱
  17. C

    Power pack or stator???

    lots of models 150 1998 but harness fuse says 20 amps on one diagram carry a few spares don't you ?
  18. C

    Power pack or stator???

    great news and feedback....could have been just a bad connection ...stay close to shore for a few trips
  19. C

    Evinrude 4hp frozen solid

    with no access the threaded area inside the lower housing try heating the bolt head. maybe the expansion can break the bond alternatively you could try freezing the bolt head ...a can of keyboard cleaner spray held upside down will freeze it the use of a 1/4 inch impact wrench with short...
  20. C

    New impeller, tell-tell just spits

    well.. you can try running/wiggling a stretch of weedeater cord up the pee hole to free up any debris.. if any or... you can try pushing some compressed air up the pee hole and retry the engine a good impeller needs to push water up the water tube it may fail at lower rpms ... in a...
Top