Search results

  1. Scott Danforth

    Pontoon guide ons

    you are assuming you know what type of trailer the OP has.
  2. Scott Danforth

    Has anyone seen one of these before

    that small boat would have been built the end of the 60's, early 70's Chris Craft would have been bought and sold about 8 times since that boat was made that was made during the micro boat glory days (same time frame as my old Wooster was made) OMC owned Chris Craft in the 90's, and most of...
  3. Scott Danforth

    Rigging boat for dry dock lift.

    to be lifted with people on board, you need to have HOP compliance (which requires Lloyds registry witness testing) and since there were many changes to LAME for the HOP rules, I do it for a living, and I wouldnt do it on my own.
  4. Scott Danforth

    Pontoon guide ons

    Help us help you.......answer our questions and we can provide guidance. so what kind of boat, what kind of trailer, got pics? we do not read minds.
  5. Scott Danforth

    Rigging boat for dry dock lift.

    HOP (Handling of Personnel) is a whole other class of product.
  6. Scott Danforth

    Rigging boat for dry dock lift.

    they lift thousands of boas per day with straps, why do you not want straps? you wont be able to lift it from the gunwales give you a hint, the transom tie downs go thru the transom and have reinforcing plates start with that thickness...... and tie it all the way down to the...
  7. Scott Danforth

    1988 Starcraft-221 Offshore-Replacing engine mount stringers

    I agree with Chuck..... youre going to find lots of rot, you will end up un-capping the hull and then doing a full restoration. so start making a cradle for the hull now.
  8. Scott Danforth

    Identification of Boat

    many times boats without paperwork are yard planters
  9. Scott Danforth

    Anyone replace their AQ water neck fitting to a plastic one?

    coming back around to this. bolt pattern is the same. Havent bolted it up yet, however https://forums.iboats.com/threads/1988-rogue-2420.486013/page-31#post-5619255
  10. Scott Danforth

    1988 Rogue 2420

    on another note, the stainless water inlet fitting I made was a bit restrictive, I had been using a stock one for the past few outings, my buddy brought back some plastic ones from Bulgaria. $14 USD vs $60 here in the states. going to modify the stainless one eventually, however the plastic...
  11. Scott Danforth

    1988 Rogue 2420

    pics of the busted carb
  12. Scott Danforth

    Volvo Penta Throttle Only Button

    Did you replace the bits under the rubber button cover as well, or just the button cover?
  13. Scott Danforth

    470 Distributor Mechanical Advance

    The HEI springs are too long for a prestolite dizzy. You may wsnt to check your part number again
  14. Scott Danforth

    1988 Rogue 2420

    Well, update required..... Pics in the AM. New carb came in last week snashed in transit. Won auction on its replacement.....
  15. Scott Danforth

    470 Distributor Mechanical Advance

    Try 19514a2
  16. Scott Danforth

    1988 GM OMC 5L points gap???

    Its recommended
  17. Scott Danforth

    Stringer repair

    if you put adhesive lined heat shrink over it, its fine. even the 304 stainless fittings rust
  18. Scott Danforth

    Fibreglass boat floor replacement - do I need to use fiberglass?

    you cant walk upright with half your spine missing...... consider the stingers hull and deck the spine of your boat.
  19. Scott Danforth

    470 Distributor Mechanical Advance

    you cant use springs from one manufacturer and expect them to work on another manufacturers distributor and expect them to work. only way to "experiment" is with a sunnen distributor machine.
  20. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    yes. the 6 bolts on the AQ PDS housing clamp are accessible only from the outside, and only when you have the drive off (or at least the upper gear box/transmission off). the system is sealed with two rubber donuts you will need to buy new.
Top