Search results

  1. R

    Reel oil (recommendations)

    Baitcasting Reels . I use Remington gun oil but does anyone know of a good reel oil ? I ordered some on line for about $10.00 a ounce did'nt work very good and cost too much .Years ago used 3 in 1 oil but they changed it and it's too heavy now .
  2. R

    Patching a hole

    What is the easiest way to fix a hole ,boat is on a lift and in fresh water . Welding is out (don't have a machine or qualified aluminum welder)
  3. R

    To decarbon or not to decarbon ?

    Got a 1957 35hp Johnson and a 2000 90hp Johnson ,mostly use the older motor , but should I decarbon these motors ? I put Seafoam in the gas tank on the 2000 . What do I use and how if I should ? Thanks for any replies .
  4. R

    Fuel pump conversion

    2000 90hp Johnson(J90VLSSS). At present am using fuel pump on vro unit ,oil side has been disconnected and am pre mixing . Is there a pulse pump that I could order to replace this one? If so what pump and how to install it . Or should I stay with the vro unit ?
  5. R

    Loose hose ?

    2000 90hp J90VLSSE. I found this hose connected on vapor pump(above primer) connection on vapor pump is horizonial going to starboard , hose is 1/8" ID and about 5/16" OD and about a foot long ,my big question is where is the connection located at . I think(?) it connects to lower main bearing...
  6. R

    Wiring(spark plug) Question

    2000 90hp Johnson J90VLSSE Have I installed wiring spark plug wires that might give me trouble . I bought United Marine mega mag 250 ssc silicone sae J2031 , these wires are blue . Should I replace or not ? I know now that 931-4922 gray wires is what is called out for . Thanks
  7. R

    Stuck in QuickStart

    What and how do you check to see if engine is stuck in QuickStart ? 2000 90hp J90VLSSS. Thanks if you can help .
  8. R

    2000 90hp Johnson model J90VLSSE loose hose

    On the air box(breather) there is two hoses one goes on bottom port side and one goes on top starboard side . The one on starboard has a T with about a 3" hose that is not hooked to anything and it is not plugged . Question do I need to plug it or is it suppose to hook up somewhere? Oil side of...
  9. R

    Fuel pump conversion

    Have a 2000 90 hp Johnson ,am pre mixing fuel but using fuel pump on the VRO unit . Fuel pump quit working got a rebuild kit on order . Rebuilt pump about two years ago , my question is , is there a pump that can replace this one and remove the VRO unit and my next question would be , how do I...
  10. R

    1957 35HP Johnson starter problem .

    Have to turn key to start position more than once to get motor to turn over , sprocket gear goes up every time . Question. Is there a way to check if it's the starter or the selanoid ? Battery and cables are good . Motor does start but takes a couple of try's . I'm sure I misspelled...
  11. R

    2000 90hp Johnson won't idle

    Model J90VLSSS . Can not get it to idle . Using primer can manage after a couple of times to get it running at WOT runs good at this point but when slowed down it dies . Here is what I'v did so far . I can get it to halfway idle using primer then throwing in gear and taking off . 1. Took all...
  12. R

    Spark plug wire

    Have a 2000 90hp Johnson .Spark plug wires looking worse for wear so decided to change but OMC Service Manual doesn't even mention anything about them that I could find so went to Marineengine web site and looked on the break down of parts and they don't mention them .Need help don't want to...
  13. R

    What spark plugs work best ?

    Have a 2000 90 hp Johnson .Model J90VLSSS whats the best plugs for this engine ? At present am using Champion QL78YC .This is used in hot climate(Texas)
  14. R

    90hp 2000 Johnson -Surging

    Took to the water after setting up for about 6 months .I did put Seafoam in and ran on muffs a few times .Went fishing Friday and motor was surging for about first 2 miles after that ran great .Decided to change inline filter and run "something" thru motor to try and get it "cleaned out". A N Y...
  15. R

    Control cables 1957 35hp Evinrude

    Put motor and controls on a aluminum boat . Controls are too long , can they be shortened ?
  16. R

    Gears Grinding when going into reverse

    2001 70 HP MERCURY FOUR STROKE . Grinds a little when going into forward but grinds a lot when going into reverse . This is a replacement motor bought from a outboard mechanic he says you have to slam it hard when changing gears . Don't sound right to me . Comments ?
  17. R

    Center console

    Finish on my white center console is a flat dull look , does any one know what to use on it to brighten it up ?
  18. R

    Fuel problem 2000 90 Johnson

    Only way to keep motor running was pumping primer bulb . VRO was disconnected years ago . How do I check fuel pump ? And NO I don't want the VRO reconnected . Thanks
  19. R

    1992 60hp Mercury-quits running

    1992 60hp Mercury Ser#0D142687 Starts up and runs about 100 yds and quits .Does not appear hot . After waiting a while it starts up and runs about 100 yds and quits again . Where is best place to start looking . My first is coil but it has three so its not logical for all three to go bad at once .
  20. R

    Eagle dept finder/Hummingbird transducer ?

    Lost transducer off of a Eagle depth finder .I have a transducer off a Hummingbird , cords are similar , spliced the cords together . Thought I'd try and see if it will work as don't have anything to lose . Does anyone know if this will work ?
Top