Search results

  1. H

    2005 J115PLSOR intake overpressure/raw gas?

    You might be right. Gentle suction on priming line (solenoid not energized) gave me a squirt of gas, but only on one cylinder bank. How do I properly check for that?
  2. H

    2005 J115PLSOR intake overpressure/raw gas?

    Too much even for 2-stroke, IMO
  3. H

    2005 J115PLSOR intake overpressure/raw gas?

    I hope it does. Just ordered one. Surprisingly cheap, but a pain to find. No, but after a minute it sort of gets to what I expect to be normal for a 2-stroke.
  4. H

    2005 J115PLSOR intake overpressure/raw gas?

    Is there a useful diagram of those connections out there? Solis manual is not too much help. Too much even for a 2-stroke, IMO. I can shoot a picture, I imagine.
  5. H

    2005 J115PLSOR intake overpressure/raw gas?

    1. Pulse 2. Not likely. Old VRO was leaking into pulse hose (I think I grumbled about it on this forum), but replacement is only 2 years old, I believe. Did not solve smoke problem (separate, but probably related issue) much, either.
  6. H

    2005 J115PLSOR intake overpressure/raw gas?

    Correct. This is a frame from a video with engine running. The line is the same line shown in the first pic, only the other side, and it was blown off its fitting. Based on what I am hearing at the local shop, it is supposed to recirculate excess gas from the crankcase back to intake. So, if...
  7. H

    2005 J115PLSOR intake overpressure/raw gas?

    Except that I am talking about pressure NOT in crankcase, but in the intake tract between throttle plate and reeds. Which should be atmospheric or less, because of the sucking action of the case. And if it is ABOVE atmospheric, as stuff spitting out of the tube suggests, where, in your opinion...
  8. H

    2005 J115PLSOR intake overpressure/raw gas?

    Didn't think of that, will check next, thanks. It does click as it is supposed, though, and I don't see how it would create overpressure, though.
  9. H

    1998 115 (E115SLECM) VRO leaking fuel

    Mixing gas is a pain, but at least you won't get your engine fried if VRO freaks out. My philosophy is, run VRO while the motor is under warranty, then go pre-mix. There are reasonably priced kits for that.
  10. H

    2005 J115PLSOR intake overpressure/raw gas?

    OK... saga continues. New powerhead, redone carbs. Engine sneezes at idle, crossflow line come off fittings (at green arrow, view from starboard), and a spray of fuel comes out of the line. Can't think of anything other than excessive intake pressure, and don't see any way for that to happen...
  11. H

    2005 115 Johnson PLSOR dies at idle

    Fingers crossed, I got it. Installed aftermarket non-VRO pump; idles OK now, pulse hose dry, smoke is down to acceptable levels. Thanks y'all for your wisdom.
  12. H

    How do I check kill switch?

    You wouldn't have had spark if kill switch were a problem. Did it suddenly happen, or was it sitting a while? How's compression? Try spraying starting fluid down carb throats and giving it a crank.
  13. H

    2005 115 Johnson PLSOR dies at idle

  14. H

    2005 115 Johnson PLSOR dies at idle

    *Sigh* Yes.
  15. H

    2005 115 Johnson PLSOR dies at idle

    Those are Torx. Six points solid. I am looking for 5 points (I believe Apple calls them "pentalobe") with a center pin. Found them on Amazon, but they might not fit through adjustment hole. I'd go with aftermarket: https://maxrules.com/VRO_04-90.php
  16. H

    2005 115 Johnson PLSOR dies at idle

    I know. I just can't seem to find five-pointed torx-like bits. I'm sure they exist.
  17. H

    2005 115 Johnson PLSOR dies at idle

    You're right, it's Torx. They do have that five-point for idle adjustment, though.
  18. H

    2005 115 Johnson PLSOR dies at idle

    Where do I buy bits for 5-point star with center pin security screws? :) I'll probably mess with it later anyways. for education and out of curiosity.
  19. H

    2005 115 Johnson PLSOR dies at idle

    There is a weird connection to vapor separator tank, so any pump simply won't fit. There is a couple of outfits that make the bracket to put on a non-VRO pump, though. Good news, the bracket plus pump runs about the same as VRO rebuild kit.
  20. H

    2005 115 Johnson PLSOR dies at idle

    It is a VRO, but oil injection was removed long ago; I am running pre-mix. I was thinking about getting an aftermarket non-VRO rig; what's the wisdom on that? Thanks!
Top