Search results

  1. S

    Must be cold...

    Everything you post is always full of elegance and grace. Thank you.
  2. S

    Must be cold...

    Seattle or western Washington and even a bunch of eastern Washington is having record weather everything. Torrential rain, wind, massive snowmelt all combined to make rivers crest higher than 100 year record river peak records. Crazy stuff and I'm sure plenty of life loss. Still waiting for...
  3. S

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    This day just gets better and better!🤫
  4. S

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    Comedy Central is now here...and I got a good laugh. Jimbo was the best but Racerone was a close second. Sometimes just working on them or painting them different is fun... And I enjoy it. My 1974 Lund does 27 with a fully loaded boat. Motor is a 1985 fully stock 30 HP johnson...or is it...
  5. S

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    Dr Tim is very correct. He has found the force. Keep testing your 25. Are the butterfly's opening all the way? The correct link and sync have been done? Boat bottom clean? Many factors here.
  6. S

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    Find a used 30 or 35 HP carb in compatible years...direct swap. Get a tach, make sure your in the rpm curve by selecting the right prop. Go on a diet.
  7. S

    1994 Evinrude 50 HP Not Charging

    Why are you replying to me, I'm not the op.
  8. S

    1994 Evinrude 50 HP Not Charging

    How many RPM's is your motor doing with the volt gauge where it's at in the picture?
  9. S

    Tilt Pin Replacement for 1987 Johnson 15 HP

    They did make a submersible stainless one. Try one made after 1992. Common problem. Or, wire wheel yours and coat it in grease...good grease. Good luck
  10. S

    2007 ETEC 150HP - won't turn off

    Might be a brp issue really. My 115 E-tec harness wouldn't turn over one winter after shutting it down for the season. Months later, I tried to start it and no starter spin or power...gauges or anything. Screwed around a little while the key was in the on position and all of a sudden the pumps...
  11. S

    2007 ETEC 150HP - won't turn off

    In an emergency, vice grips to the fuel line always works.
  12. S

    What prop to use 50hp evinrude

    Proper prop pitch is also done, on a boat, fully loaded and properly trimmed. Once achieved, you must be in your rpm range.
  13. S

    electric start

    Seems this issue already came up in 2017...see pic. I say build it....prove everyone wrong!
  14. S

    What prop to use 50hp evinrude

    Can't quite tell but Michigan props have their own thrust washer...I recently padded one out using stainless steel washers modified by me to fit over the shaft. Proprietary system and could be your problem.
  15. S

    1994 Evinrude 50 HP Not Charging

    Typically if the red wire does not go out to the battery, it fries the rectifier. (Dead heading)
  16. S

    electric start

    You can always do it by damaging the crankshaft threads with a drill gun on the flywheel nut like others but most likely no one here will recommend it. Cast your own flywheel perhaps and mount that lawnboy starter ...I've seen harder things made. 🤪
  17. S

    J90 MLCRD-'84 XFlow. Upper water tube grommet part #.

    Anyone in your local area sell brp Evinrude parts? If not it depends what country you live in. Post your country.
  18. S

    Johnson Evinrude 130hp vro pump

    If your healthy enough to inspect it you may find it needs much less than $150. Also depends on your mechanical ability. Inspecting cost nothing. But regardless of your issue, having a bad back and boating don't go hand and hand. I'd wait and do it right. Always worked best for me.
  19. S

    Johnson Evinrude 130hp vro pump

    To answer your question directly, no do not use aftermarket stuff. Rebuild it...fuel diaphragm only most likely... But do the other things first. Question, if your mechanic diagnosed this, why didn't he just fix it?
  20. S

    '88 Johnson 30HP bogs down on full throttle

    NOT good enough....compression. First line of racerone's comments. Time to give up on this motor. Did the mechanic who "tuned it up" know about the compression numbers? Might want to seek out someone else if he did.
Top