Search results

  1. C

    Free manuals?

    sold that one $150 CDN to a long time friend after the usual refurbish coils points wires plugs carb job etc... I just recoup my purchase and parts $$ ...keeps me busy in the cave during winter :-)
  2. C

    Slow speed needle valve for 1971 25hp Johnson

    try tim's outboard used parts also classified want ads on AOMCI site
  3. C

    Slow speed needle valve for 1971 25hp Johnson

    try some heat shrink tubing over the threads ...remove after
  4. C

    54 johnson 3hp

    Jw are nice little kickers very easy to service if not mistreated . point opennings can be set at the highest point of the cam lobe at 0.020 openning and it should run fine. Add one-two drop of oil on the cam rub felt the idle circuit on the carb has a side channel from the bottom...
  5. C

    54 johnson 3hp

    don't assume all is bad till you look inside. but probably does have bad coils after 40 y. a $100 is waste if you plan to hang it up another 40 years in a barn and look at it but if you want to go fishing , give it to the kids or grand children go for it. Fishing....best to...
  6. C

    54 johnson 3hp

    reading material to start with http://www.outboard-boat-motor-repair.com/Evinrude%203%20HP%20Lightwin%20Outboard%20Boat%20Motor/Evinrude%20Johnson%203%20HP%201952-1967%20Carburetor%20Tune-UP.htm...
  7. C

    Free manuals?

    carbon core is highly resitive and produces less radio interference from radiated High freq. energy. it was from what I understand .. .a solution to limit noise in the A.M. band radios of the time....and today if you are a A.M. listener. thanks to ohms law which specifies that the...
  8. C

    Free manuals?

    looks much to expensive... just buy 4 feet a the bike shop your BEL # is different ....mine is from NAPA canada watch out for shipping $$$
  9. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    you should get the serv manual & EV diagnostic software to see if any faults are logged. your dealer should have given you a fault log dump (history and current faults) they can just email it to you in PDF format since the EV software keeps a log in their shop system (windows PC)...
  10. C

    Free manuals?

    if you do decide to work (refurbish) the coils points condensers may as well do plug wires and boots... you will need some 7mm metallic strand wire (local bike shops may sell you some for $2 a foot or so. DO NOT USE CARBON FIBER PLUG WIRES !!! keep the little mini rubbers on the coil/wire...
  11. C

    Free manuals?

    no need for big books simple motor http://www.leeroysramblings.com/OMC_6hp.htm http://www.leeroysramblings.com/johnson_magneto.htm replace impeller gear case oil use new nylon washers clean the carb orifices with carb cleaner blow dry if the float is cork and all crinkled...
  12. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    btw check out the ETEC board ...good search utility and lots of help available to https://www.etecownersgroup.com/?forum=136486
  13. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    If it runs great and starts great injectors likely ok. compression likely ok also so you are missing fuel as the 3rdelement. do you recall when all this issue started? how are the filters ...new ..old... crudded . tank venting ok ? did you inspect the return filter #7 on...
  14. C

    Johnson 115 ocean pro running on one cylinder

    may as well check for sparks on the dead cyl.
  15. C

    hard to start when warm

    nobody could start my old Merc 500... all it needed was special TLC and started everytime ... ++ racerone comment
  16. C

    Durbans Johnsonator outboard motors .

    9 years later ??? this better work :-)
  17. C

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    The cross pin is hard to see in the photo supplied by OP but this seems to be a winning solution based on this parts picture
  18. C

    1980’s Evinrude - Temp Warning System?

    https://www.amazon.ca/MG-Chemicals-Silicone-Transfer-Compound/product-reviews/B005DNQWQU/ref=cm_cr_dp_d_show_all_btm?ie=UTF8&reviewerType=all_reviews good glue to mount alarms sensors metal over metal good excellent heat transfer
  19. C

    1980’s Evinrude - Temp Warning System?

    Mount & hook up a few of these on a piezzo buzzer ! chose 60 (140 F) or 70 C (158F ) normally open contacts will close when hot...
  20. C

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    cross pining it may work ???
View older results
Top