Search results

  1. bspeth

    Setting points/dwell

    I am flushing on muffs while turning the engine over to check dwell or not necessary?gonna put those pups in at #1 tdc so it should be damn close right?full tune on the agenda for tomorrow.thanks-B
  2. bspeth

    Did Iboats change format?

    Is it my computer or has the site changed its layout?
  3. bspeth

    FSM Pressure test link

    Anybody got this handy? Maybe we could add it to adults only under pressure testing? Just cant find the sucker even though I know ive read it five times.
  4. bspeth

    R drive question

    I took off my drive yesterday and laid it down on its side while I messed around with the orings.It seemed to leak a little oil out of the water drain hole.A small amount but noticeable.The drive was pressure tested before layup and held fine. Is this a problem or just a result of laying the...
  5. bspeth

    2.5L gear ratio

    what gear ratio should back a mercruiser 2.5L? Also can gen 2 interchange on the same transom as r/mr. Thanks
  6. bspeth

    new points

    I have been told that new points come with a coating on them that needs to be removed,how do you guys remove it?
  7. bspeth

    pulling prop

    My buddy has fishing line wrapped all up in the prop.Honda out board with all the controls.I am not too familiar with outboards. Should he just put it in forward and take off the nut,or does he need to ground out the coil to prevent starting?Thanks-Blair
  8. bspeth

    Olympic rink size

    I know there are a lot of Canadians on here and I was wondering if the rink is international size or NHL size. Usually I can tell at a glance but I have not watched NHL since the playoffs last year.Thanks -Blair
  9. bspeth

    Prop selection

    My purpose of prop change is damage to my old one and fine tuning. Current prop Michigan wheel 15.25x15 3 blade aluminum.84 beachcraft funrunner 18.5.Approx weight 24-2600 lbs. Merc 229 3.8l v6. 185hp.WOT at 5000 ft was 4400 and about 31 mph on the dash gage.Trim full down position.I would like...
  10. bspeth

    new style shift shaft bushing install

    does this call for locktite or any sealant.R drive6683545
  11. bspeth

    what did you get your boat for christmas?

    Stereo and speakers,and of course I will need a roto zip to cut it in.
  12. bspeth

    gear ratio info

    R drive6683545. I looked on the stickys but my year (84) has quite a few different ratios,and the serial nunbers listed are all the same range for each ratio. Trying to figure my prop slip.Drive is backing a v6 229.Thanks
  13. bspeth

    Lake Almanor

    CA.Anybody have any insight on this lake? Trying to book a cabin with a dock this summer.Thanks
  14. bspeth

    new style bell housing bushing

    any bobdy know the part no. of the plastic washer you are supposed to install with this bad boy?23-805041a 2. Thanks
  15. bspeth

    How to check timing advance

    Engine ser#6681735 3.8l 229 v6 with points ignition. How do I properly check the timing advance?
  16. bspeth

    New style shift shaft bushing

    Drive 6683545 R alpha. The part number for the upper shift shaft bushing is 814308.I think this is the old style and should I be replacing it with the new style? I pulled a part number from a previous post 23 805041A2,could you guys tell me if this is the right bushing set for my drive,or if all...
  17. bspeth

    Drain points on a 3.0

    My boss has a 3.0 and I want to check it for him to make sure its drained proper.Dont have SN. it probably late 90s alpha one gen 2 drive. Engine is carbed.Can you tell me the drain points,I can follow the intake hose but its nice to hear from people who have actually done one.Thanks-Blair
  18. bspeth

    relplacing bunks

    Any tips on this? What do you guys do send the wife out on the lake while you replace them with pre built ones and have her pick you up after a while?Whats the best kind of carpet?
  19. bspeth

    Tune up with points

    I have been reading dons instructions for tune up with points and I have a question. The jumper wire hooks up to the center post on flame arrestor and the other end hooks up to what? the post states center post on coil but the picture shows it hooked up to - side of coil.Does it hook up the the...
  20. bspeth

    Testing points

    Can I do this with a regular digital multimeter with the resistance setting? If so how do I do it and what should the resistance be? I saw a good deal on a dwell meter but it does not have a setting for points.Thanks-Blair
Top