Search results

  1. bspeth

    Trolling with a jettison release

    Going to Lake Shasta and I read that the Bows are down deep 50-70'. I will be using a jettison release that drops the 4oz sinker when a fish strikes.Any Idea how much line I will have to let out to get those depths at 1.5 to 2.5 mph on gps?
  2. bspeth

    Radial or Bias

    What are the advantages and disadvantages of each type of trailer tire?
  3. bspeth

    Greenball trailer Tires from Costco

    Anybody used these pups?
  4. bspeth

    Head gasket

    Does the head gasket go on dry? I plan on coating the bolts with perfect seal.1956 Evinrude 7520.Thanks-B
  5. bspeth

    Evinrude 6hp

    1975 evinrude 6 hp 6504r.When I throttle up after a long troll the throttle is really slow to respond and almost seems to want to stall. The only other thing is it will stall once or twice during the first hour and a half of operation at trolling speed.I can also hear the motor sucking air about...
  6. bspeth

    Part supercession for condenser

    Hi,I ordered part m/qs 6324 condenser and I was sent 8m6001249. Will this condenser work and is it the proper part for my ignition? The old one looks different as it has an insulated strip of copper as a lead that is about 1/4 inch wide and slightly thicker than a piece of paper. engine ser...
  7. bspeth

    7520

    Got the 7.5 fired up in the tank,carb ran good but need to get on the lake to adjust it.Got it to idle in gear until the cam follower was not touching the cam at all. Any way,I need to replace the exaust cover gasket probably because it was baked.It was dripping a little water around the aft...
  8. bspeth

    Trim will not go full down

    Last fall I did a bellows job with trim senders along with all the routine layup stuff. I noticed a few weeks ago that the drive was not trimmed down full. Almost but about 3/4 to 1 inch to go on the trim cylinder.I must have heard the pitch change on the pump and thought it was home. Now that I...
  9. bspeth

    Couple more 7520 questions

    1) Does the 303347 oring just set on top of the 303357 lower bearing to driveshaft seal? I see a little cup on top which it seems like the o-ring will slide down into eventually,compromising the driveshaft seal between there and the 303356 driveshaft to crankcase plate. 2) How does the filter in...
  10. bspeth

    One more 7520 question (then I got er)

    For some reason the water pump base will not seal to the case. I have looked at it and it is just 2 clean gasket surfaces so I don't see why it would be leaking but it is showing bubbles under pressure which it will not hold.I have checked for cracks in the case and water pump base.Are the...
  11. bspeth

    '56 evinrude 7520 shift shaft bushing replacement

    Ok so I repaired the water pump and pressurized the gear case and found that I had two leaks before. I thought I had found my only problem in the driveshaft seal in the water pump base but the upper gear housing shift rod bushing and oring are leaking also. Does anyone know the procedure for...
  12. bspeth

    56 7.5 Fleetwin gear case removal

    I fired her up today and the carb seemed to run ok in the tank. She is not pumping water as nothing came out the exaust relief port and it just seemed too hot and too loud.I went to drop the lower to see what parts I need for a parts run and I cant get it to drop.There is no coupler like on my...
  13. bspeth

    1956 Evinrude 7520

    Does this model have a sealed gear case?The manual is not clear on that.Thank you.
  14. bspeth

    75 6hp Rude

    I want to replace my slow speed knob as it is missing. It appears that a PO cut the slow speed needle down so that it does not protrude through the engine cover any longer.Can I just get a new needle and unscrew the old one in favor of new? Or do I also have to remove the packing nut and washers...
  15. bspeth

    Run on

    I have a friend and his boat runs on after shutting off the ignition while forward momentum is sloeing but not stopped,please flip me a few ideas of what to check out. Thanks.
  16. bspeth

    Autoride

    Still looking for a Yukon,does anybody have experience good or bad with auto ride?My thought is that it is one extra expensive system to have fail but I don't know about its durability.
  17. bspeth

    Looking at some Tahoes and denalis

    Looking for some input good or bad.2001-2004.Thanks Crap wrong section.Can this get moved to towing please?
  18. bspeth

    Has this happened to anyone?

    I was replacing my ujoints and I couldn't get the c-clips to seat properly. Pressed in one side and set the clip which left not quite enough room for the other c-clip.While tapping one side over the other clip would come un seated.I struggled with this for a while until I noticed a little gear...
  19. bspeth

    Shift cable

    So since the support tube is integrated into the new cables,are you guys full assembling the aft side of the lower cable before inserting it through the bellows and through the transom? it just seems like it will be hard to get the core wire through with the end being rigid.Thanks
  20. bspeth

    Alignment

    My alignment is pretty good,but I want it perfect. The coupler splines are witnessed at 10:30 on the bar when I pull it out when the engine is in the tightest quadrant. Does that mean I need to reisae the stbd side of the engine a touch?
Top