Search results

  1. M

    Boat buckle tie down location

    Want to install these new boat buckles on my trailer. Not sure if either location causes an issue. Need inputs please. Thank you
  2. M

    Water separetor question

    Might be a stupid question but does the fuel water separator do a good job at filtering out particles from the boats built in fuel tank?
  3. M

    Outboard install question

    Getting ready to install a new to me yamaha 130 hp 2 stroke on my wellcraft 190ccf center console. Lower bolt holes have these thick square metal plates on the inside (ignore the thin plate with 2 screws used to hold the bolt head when tightening. Think it's OK to leave the square plates as they...
  4. M

    Vhf antenna question

    I have a new to me boat which came with a Shakespeare vhf antenna but no radio. I'm installing a uniden um385 have 2 questions. Does the end of this cable look normal? Should I be receiving communication at my house? I'm about 40 min from Salt water and 20 min from the Delaware river...
  5. M

    Yamaha v4 prop shaft carrier nut torque

    Replacing prop seals and bearing carrier o ring. Got the carrier out but wanted advice on using antiseize on the big carrier retaining nut threads. Good or bad idea? Also need the torque spec for that big retaining ring nut. Thanks 2001 yamaha 130 hp v4 2 stroke
  6. M

    Rigging preference

    Just checking which is preferred bundling the excess harness lengths at the helm under the center console or at the stern before it passes through to the outboard? Some of my harnesses have a lot of extra length. For what it's worth it's a 1997 wellcraft 190ccf with 2001 yamaha 130hp v4 2...
  7. M

    Yamaha 130 fuel connector

    Rigging a 2001 130 v4 2 stroke. Looks like yamaha wants a fuel hose from the primer all the way up to the filter with no quick disconnect coupler. Was thinking about adding one but all the Rigging coming out of the motor well is going to be inside a Rigging tube with the exception of the fuel...
  8. M

    Wellcraft 190 ccf engine install

    getting ready to install a 2001 yamaha 130 v4 2 stroke on my 190 ccf. original engine (johnson 115) was installed so that cavitation plate was about 1 inch from the bottom of the boat (boat uses a stepped transom with about 7 inches setback). Do you guys advise just mounting the yamaha so that...
  9. M

    Yamaha key switch mount horizontal

    I have to mount my key switch panel sideways for my 2001 130 v4 2 stroke due to space issues. This puts the key switch in a position that makes it look like it's on even when off. I tried rotating the switch 180 degrees but same thing. Due to the flats on the switch body and panel. Any way to...
  10. M

    Mounting bolt tab?

    Getting ready to take the johnson 115 off my 97 wellcraft 190ccf center console. Lower bolts have some kind of tab over the head of the bolts. What is the purpose of these?
  11. M

    Yamaha 2 stroke oil hose

    I have a new to me 2001 yamaha 130 v4 2 stroke. Previous owner cut the oil hose about 2 feet hanging outside the motor. Does the rubber oil hose from the remote mounted tank run all the way under the hood to the main tank or am I supposed to have a different material hose under hood? If so I...
  12. M

    Yamaha rigging

    Anyone have any ideas for a clean rigging install? Yamaha 130 v4 2 stroke. Was planning on using the rigging tube from Yamaha that fits into a corresponding motor well fitting. Only problem is my steering cable passes through this opening so not sure how to isolate the ribbed rigging tube from...
  13. M

    Yamaha 130 mounting height

    Getting ready to mount my 2001 yamaha 130 hp v4 onto my 1997 wellcraft 190 ccf. It has a stepped transom. Should I make the cavitation plate even with the very bottom of the keel? Or raise it 2 inches? Currently has a johnson 115 and two my eye the cavitation plate is 2 inches above the bottom...
  14. M

    Yamaha 130 hp v4 2 stroke

    New to me motor. 2001 yamaha 130 hp. Power trim relays click when activated by trim switch but no movement or noise from trim motor. Anything to check? Motor sat for 2 years. Chance the motor might be stuck from sitting?
  15. M

    Yamaha which tach?

    I'm getting confused. Can someone give me the part numbers for either a analog tachometer or digital yamaha brand tachs. Prefer the multi guage with power trim indication. I have a 2001 130 hp v4 2 stroke with remote oil tank. I will be using a 704 binnacle remote control and a yamaha key switch...
  16. M

    Yamaha remote oil tank location.

    So it looks like I'm going to have to put my remote oil tank for my Yamaha 130 v4 in my center console and run a filling hose from a deck fill cap cut into the side of the console. Boat is a 1997 wellcraft 190ccf I know the remote tank harness is long enough but what to use for the hose from...
  17. M

    Multi function yamaha tach

    2001 yamaha 130 v4 2 stroke. Want to install either the analog tachometer with oil and temp warning and trim position indicator all in 1 or the digital version of the multi tach. Using a 704 binnacle remote with a separate key switch. Also using a remote 11 quart oil tank. Under the hood next to...
  18. M

    Yamaha 130 oil tank

    1999 yamaha 130 v4 oil injected. What is this capped off pipe on the bottom of the engine oil tank? I see one oil hose that comes from the remote tank and 1 hose out the bottom of the engines tank going to oil pump. Not sure what the other capped nipple is for on the bottom of this tank?
  19. M

    2001 yamaha 130 v4 2 stroke carb kit

    Anyone know if a oem carb kit comes with enough parts to do 2 carbs or do I need to order 2 kits? Looks like kit is around $150 each!
  20. M

    Yamaha 704 binnacle remote install

    1998 wellcraft 190 ccf center console. NEED to remove omc wide controller and install a 704 remote. Hole for 704 remote is much narrower than the omc hole. Here's some pictures. Thinking of a way to cover the too wide hole in the console. Would a sheet of abs plastic work to screw to the console...
Top