Search results

  1. M

    Yamaha 130 v4 idle mix screws

    My 2001 130 v4 loads up when running at a fast idle say 1100 to 1500 rpm range. It doesn't stall but you can tell it's not as smooth as it should be. I set the screws to factory spec bur may need some finite adjustments? On my last 115 v4 I remember not noticing a perceived change when adjusting...
  2. M

    Yamaha 130 hp oil pump rod adjustment

    My 2001 130 hp v4. When I adjust the oil pump lever clip at the oil pump arm I'm having a little trouble. If I adjust it so the lever hits the pin on the pump (low speed throttle closed position) it short changes the pin at full throttle. It just about makes it to the full throttle pin on the...
  3. M

    No feedback helm question

    Just wondering if it's OK for there to be about 2 inches of back and forth when you push on the outboard as if trying to steer left or right? I know the design of the helm won't allow you to manually steer the motor when pushing on the motor one way or other but I have little play back and...
  4. M

    How to video cavitation plate on the water

    I don't have anyone to go with me plus I'm trying to keep weight the same in the boat for testing. I believe my motor might be mounted too low. Anyone have suggestions on how to rig a camera to see the cav plate when underway?
  5. M

    Yamaha 130 2 stroke height

    1997 wellcraft 190ccf center console. 2001 yamaha 130 v4 20 " . Noticed a good deal of porpoising and I can only trim up not even 1/4 ot the trim guage. Also seems like a lot of spray ( whole back of the boat gets wet after running). I can't go back and see where the cav plate is when planing...
  6. M

    Outboard mounting bolts

    I have a 97 wellcraft center console with a yamaha 130 hp outboard. I think I want to raise the motor 1 hole. I mounted it 2 months ago with 4000 silicone and new bolts/nuts. The bottom bolts are in a slotted section on the motor bracket. Think I'll be ok just loosening the nuts (the nuts are...
  7. M

    Evinrude 30 hp compression question

    Hi working on a 1988 30 hp evinrude 2 stroke 2 cylinder. I forgot to check compression before removing lower unit. Tested and only getting 75 psi on both cylinders. Is there a difference in results if tested with lower unit removed? I know I could just bolt it back on and try it again but just...
  8. M

    Yamaha 704 binnacle remote question

    Anyone know why the 704 remote doesn't have a safety lockout like the 703 where you have to squeeze the button to shift out of neutral? Not talking about throttle only just regular shift and go. Seems dangerous in that if the motor is running and you accidentally bump into the shift lever the...
  9. M

    Yamaha 130 v4 prop question

    Got my 2001 yamaha 130 v4 2 stroke on my 1997 wellcraft 190ccf center console out on the water today for the first time. Felt a little slow to plane in my opinion. I checked top speed with a GPS speedometer got up to 47 mph at 6000 rpm. My boat only had me on it and 50 gal of fuel in the tank...
  10. M

    Oil fill bezel ??

    Hi I have a 97 wellcraft 190ccf center console. I installed a oil fill tube in the side of my console but it is a little difficult to use as it's mounted flush. I found this picture of almost the same boat but with a angled bezel for oil fill. I tried looking on internet but can't find it ( not...
  11. M

    130 v4 tach question

    Hoping someone can help me with what I need. 2001 Yamaha 130 v4 2 stroke. I installed a new old stock multi tach with the round connectors. I have a short adapter to go from round to square from the trim and oil harness. Couldn't get trim to work on gauge so I bought a separate Yamaha trim...
  12. M

    130 v4 oil tank refilling point

    I want to run my 2001 130 v4 on a 6 gallon tank of pre mix fuel before using the main tank in the boat. I placed a mark at the current level in the engine tank (after letting it fill from the on boat sub tank) I want to go through maybe 3 gal of the 6 gal tank and then lift the hood off and see...
  13. M

    Seat snap on cushion replacement

    Anyone know the brand of these seats in my 97 wellcraft 190ccf? Would like to get replacement cushions this isn't my boat in the seat picture but same seats
  14. M

    Trim guage dash question

    Looking to put a trim guage in my dash but the wood is so thick I won't have any room to put the retainer on the back. I was looking at yamaha specific trim guages and they are a lot longer. Maybe go that route?
  15. M

    2001 yamaha 130 v4 trim guage

    Trying to get my trim guage working. 2001 v4 130 2 stroke. New old stock digital tach/trim guage combo. Just getting the bottom bar lit up on guage after powering on. Got another sensor and still not reading at guage. New sensor reads 276 Ohms at 1 position then smoothly changes to 4 Ohms at...
  16. M

    Yamaha 130 run in barrel

    2001 yamaha 130 v4 2 stroke. Just installed. Idle is low. I ran it on muffs. If I run it in a barrel is that the same as running it in a lake? Just concerned with setting the idle mixture screws and idle speed before I take it out in the river. Thanks
  17. M

    Bilge sump question

    I have a 1997 wellcraft 190ccf center console. It has a sump area where the bilge pump lives. It's sealed with epoxy substance but I noticed water enters from the left side of the sump depression. Looks like its by design unless someone says otherwise. Not sure if that's intentional or if i...
  18. M

    Yamaha 130 hp idle adjust

    Just fired up new to me 2001 yamaha 130 hp 2 stroke. Rebuilt the carbs, new fuel pump, new spark plugs. I started it on the muffs at my house. Idle is low 5 to 600 rpm. I left the 4 idle mixture screws at current setting when I redid the carbs. I checked the roller cam pickup point is in spec...
  19. M

    Wellcraft 190 ccf

    I have a 1997 wellcraft 190ccf center console. In the bilge at the aft end bottom of the boat is a oval depression about 1 inch deep which is where the bilge pump sits. This area is covered with a hard waxy looking sealant. I noticed a little water in that depressed area and as I dry it up more...
  20. M

    Yamaha 130 2 stroke oil injection question

    Ready to put my 2001 130 v4 into use. It sat for a year or so. I've rebuilt the carbs and noticed the injection oil is present at the individual outlets in the intake manifold. Does thus suggest the system is ready to go? I've tested the level sensors and they work fine and also confirmed the...
Top