Search results

  1. 1

    Trim question for the new 150 HP SeaPro Outboard.

    I read the manual, it goes into how the trim/tilt functions but doesn't address this specific issue.
  2. 1

    Trim question for the new 150 HP SeaPro Outboard.

    Trim question for the new 150 HP SeaPro Outboard, that I just purchased related to the tilt. When tilted up all the way it hits the stainless Rod Holders and will scratch the cowling. I know some of the other brands (E-Tec's) have a setting to limit the travel, is there such a setting for this...
  3. 1

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    Update # 2: This motor in question was purchased used from a boat shop in San Diego, he now thinks it's the injectors and asked that we drive it down from LA so he can remove/clean/replace the injectors. He also thinks this was the original problem with the boat dying when moving between gears...
  4. 1

    New 150 HP Sea Pro

    appreciate the feedback, the motor will be installed next week. I guess I'll learn more about it when I pick it up. Jerry
  5. 1

    New 150 HP Sea Pro

    Purchased a new 150 HP Sea Pro last November, should arrive in June. I'm trying to see if others that already have this motor like/dislike them and why. Can't find any threads on them, appreciate any input. Thanks/Jerry
  6. 1

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    Update: When we had the motor in the shop they replaced the #7 filter, however after reading your reply I wanted to check it. It was clogged with residue that I can only assume came from the gas tank on the boat. We changed the filter and switched to a new external tank, it didn't change how...
  7. 1

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    We have a 250 E-Tec that starts and immediately dies, it take about 20 to 25 times of this before the motor catches and stays running. Once running it runs great and will restart within 1 or 2 tries. Just had it in the shop to have the shift switch changed, also changed plugs and the # 1 coil...
  8. 1

    2012 15 HP Honda Outboard cutting out when giving it throttle.

    I looked for this pipe, don't see it on this carburetor. I'll look at the daewings and see if they match whata I have. Thanks.
  9. 1

    Honda BF15D will not stay running (Purchased Used)

    It was severely overheated, so I don't think there was any "Protection" system shutting it off. The impeller housing was partially melted, even found parts of the impeller stuck in the thermostat. The thermostat housing was deformed and even the throttle cable was melted "Stuck". But once...
  10. 1

    2012 15 HP Honda Outboard cutting out when giving it throttle.

    I have a 2012 Honda 15 HP (BF15D3SHS) tiller handle outboard that I recently purchased, had several issues due to a overheating problem when I purchased it. Now the only problem left is it wants to cut out while giving it throttle. It will idle fine all day, but if I give it a quick turn on...
  11. 1

    Honda BF15D will not stay running (Purchased Used)

    Thanks for all the help and suggestion on this post, after replacing all the cooling related parts (and a few others) I did get the motor running. Thanks.
  12. 1

    New Tohatsu 3.5 HP (MFS3.5C) Won't start after it's warmed up.

    Never really solved the problem, but after trying all the different suggestions listed here it just seems finicky. However the best solution so far has been to loosen the gas cap a little bit, it seems to restart much easier, I'm assuming the release valve on the built-in tank isn't enough air...
  13. 1

    Honda BF15D will not stay running (Purchased Used)

    Update # 2: My new compression set came today, it had the correct size fitting for this motor, both cylinders came in at 110 Lbs. each. Still starts easy, but only runs for 30/40 seconds & dies, the green light in front stays on the entire time. The water bin I'm using to run the engine in...
  14. 1

    Honda BF15D will not stay running (Purchased Used)

    Update: Have now installed the temp sensor and also replaced the throttle cable (Old cable was frozen) everything is back together and look rights. The motor starts easy and sound great, but will only stay running for about 30 seconds or so, during this time the green light is on. to me it...
  15. 1

    Honda BF15D will not stay running (Purchased Used)

    Per the seller the motor was only used for less than 20 hours in fresh water only, they said the temp sensor was broken while changing the spark plugs, this seems feasible as the sensor is directly in the way of changing plugs. I should have the new sensor installed this week, also hope to have...
  16. 1

    Honda BF15D will not stay running (Purchased Used)

    I need to get a different adapter for my compression tester as the spark plug hole is very deep/narrow and won't fit. I'll find the correct fitting and post the readings.
  17. 1

    New Tohatsu 3.5 HP (MFS3.5C) Won't start after it's warmed up.

    it does, tried different positions. I can try again just to confirm.
  18. 1

    New Tohatsu 3.5 HP (MFS3.5C) Won't start after it's warmed up.

    Have a new Tohatsu 3.5 4 stroke motor for a Dinghy, it's starts easy when cold and seems to warm up okay. Once we're under way and decide to stop it won't restart, very frustrating as it's so easy to start when cold. Open gas valve/open fuel tank air valve/choke, we leave the choke out until...
  19. 1

    Honda BF15D will not stay running (Purchased Used)

    Hard to start and dies quickly.. Just purchased a used 2012 15 HP Honda outboard, the seller stated it only had about 20 hours of uses. When purchased they made me aware that the temperature Sensor was broken and everything else was fine. (Temp sensor is on order and should be here in a few...
  20. 1

    2013 E-Tec 250 HP (Dies when shifting from F/N or R to N)

    Thanks Crosbyman, Went to the E-Tec site you mentioned above, apparently this is a problem for a lot of folks. After reading several post I seen that many users replaced the shift Switch and still had the problem, we'll be taking it to the dealer this week. I'll do a follow up post once we get...
Top