Search results

  1. R

    Sneezing from underneath flywheel

    There you go.-=---Pull the head off.----Lucky you if it is a blown head gasket.
  2. R

    Sneezing from underneath flywheel

    Motor does not sound healthy at all.-----Post the actual compression values.
  3. R

    Best years for 70-75hp Johnson/Evinrude outboards

    The 49 cube 70 ( 60 prop rated ) from 1979 to 1988 would be my choice.----A V-4 model 90 / 115 HP OMC would be a better choice.-----But needs to be cheap for rebuild.----Great , simple , reliable motors once properly rebuilt.-----Any one from 1980 to 1998 model year.
  4. R

    Can I lubricate the cutlass bearing with something so I quickly test forward and reverse on the trailer

    With the boat in the water there is water under pressure to keep the packing cool.----And a slight drip of water should come through the packing when underway.----Careful if you are going to run with dry packing.
  5. R

    no speed

    Might be running on 1 cylinder.
  6. R

    1979 Johnson 115 HP - Oil/Gas Leak

    I can not see or touch your motor.----On this 45 year old motor I would first do a compression test.----Post the actual values here.-----The powerhead is removed as an assembly to change the gasket.----Factory gasket today is improved over the original one.
  7. R

    1998 115 Evninrude E115SLECM Testing the Rectifier

    A diode blocks current in one direction.
  8. R

    1979 Johnson 115 HP - Oil/Gas Leak

    Gasket between powerhead and exhaust housing is my guess.
  9. R

    200 HP Evinrude/Johnson Carb Kit and Rebuild

    Do you push the key in and HOLD IT IN while cranking it over ??----Do you advance / open throttle ?-----Have you inspected starter motor ?-----All that cranking may have damaged it.------The primer valve puts fuel directly into the motor.-----This fuel bypasses all the jets and metering circuits...
  10. R

    1986 2 stroke 3 cyl major issue

    Remove water cover that fits over the block.-----Inspect water cover and block.-----Clean gasket surfaces.----Install new gasket with a LIGHT coat of sealer.-----About 80 INCH LBS on the screws.
  11. R

    '86 Evinrude 60 VRO E60TLCD with water in #3

    Sorry ----There are no mixture adjusting screws on these 60 HP carburetors.
  12. R

    200 HP Evinrude/Johnson Carb Kit and Rebuild

    In many places the shop rate is $2.00 / minute !-----And in the interest of shop efficiency new parts can be cheaper than cleaning them.--Complete kits save the shop " waiting / running around " time.---Customers do not like to see " labor only " invoices !-----Working at home is different.----I...
  13. R

    Is this oil okay for my 1960 Johnson Sea-Horse JW-16, 3 HP, 2-cylinder? And is 16:1 the right fuel mix?

    On many OMC models the BRONZE BEARINGS for the crankshaft are well designed.----I work on the wonderful 5.5 / 6 HP models and rarely see any issues at 50:1 on these bearings.----On 50 year old motors they are usually just like new.----Run the 1960 model 3 HP at 24:1 ratio.---The 1964 and later 3...
  14. R

    200 HP Evinrude/Johnson Carb Kit and Rebuild

    There is very little that goes wrong with these carburetors.-----What is your motor doing / not doing?-----Most boat shops have these small diameter fuel line on a roll.-----crowley marine-----evinrudeparts.ca-----Are 2 places that would have these fuel lines.
  15. R

    '86 Evinrude 60 VRO E60TLCD with water in #3

    The exhaust plates are likely warped.--They develop a leak.------And after 40 years these wonderful motors need some attention.-----Perhaps not what you want to hear.
  16. R

    Tillotson TC-5E float needle valve

    Perhaps I missed them.----But what are the actual compression values on this motor?
  17. R

    '86 Evinrude 60 VRO E60TLCD with water in #3

    Likely the exhaust gaskets ( 3 of them ) have a leak.------Compression should be 140 + on it.-----Rempove cylinder head to inspect and replace the 3 exhaust gaskets.----If water gets on any bearings it spells death for the motor.
  18. R

    1994 200 HP Venom

    Charge your battery.-----Load test your battery.
  19. R

    Learning to wake board at 48. What am I doing wrong?

    More than 50 years ago at Johnson dealer , customers came in.-----They knew I did a lot of waterskiing ( including deep water backward starts on trick skis ) if you believe it..-----They asked if I was available to help one of them.------In the boat I observed the one much older than me fall...
  20. R

    Costa Coat

    Post #1 says you could not get between boat and the wheel wells ??------I guess I can't read or think.
Top