Search results

  1. nola mike

    No reverse after impeller replacement

    So with the drive assembled but not installed you're able to get all 3 gears by turning the intermediate shaft?
  2. nola mike

    Buy a used block will parts swap?????

    I'm getting a 1989 at Crowley Marine
  3. nola mike

    Mercruiser 3.0 Alpha One Gen 2

    Only one flapper below the rubber exhaust connector, that would be a good guess as to what you're seeing.
  4. nola mike

    mercruiser lower unit install

    Check the upper drive shaft area for a buggered seal. Also the early gen 1s had an o ring on the shaft that could get caught up there.
  5. nola mike

    Buy a used block will parts swap?????

    Offhand I can't think of anything that would keep you from swapping either a long or short block. Afaik all of the 470 changes involved the accessories. That said, you're going to have a hard time finding anybody that knows year to year changes on these engines in that kind of depth.
  6. nola mike

    Stupid me, no oil

    Well, I've done about 40 miles and all seems well. Haven't pushed it too hard, but ran at 3800 rpm for a while today. At speed it's steady 65 psi pressure. Hot engine at 600 rpm is 25 psi, which seems lower than prior but IDK. Comes up to 40+ psi at 1k rpm. No noises. Hopefully dodged a bullet.
  7. nola mike

    2011 Crownline 18SS Issues

    Do you have 12v at the cannon plug? That connection can cause problems
  8. nola mike

    350 MPI reman alpha wont start again

    The point being, the problem isn't solved...it's waiting to leave you stranded.
  9. nola mike

    '04 Merc 25hp dead(ish) cylinder

    Been chasing some poor running for the last few weeks. Originally was running well, but had a couple of episodes where it died at speed, difficult to restart. Noticed fuel leaking from somewhere around the carb. Rebuilt the carb with a crappy kit. Took it out once and all the gaskets...
  10. nola mike

    Outdrive oil leak..

    IIRC the area between them is normally dry. the lower is exposed to water on one side and the upper to oil. If the upper fails oil will fill the cavity whereas if the lower fails water enters the cavity and rusts the gear. On mine the gear needed a speedi sleeve on one of the surfaces. EDIT: I...
  11. nola mike

    Outdrive oil leak..

    If it was leaking it means both seals were bad. I can't remember off hand why the upper would need to be changed though if the lower has been replaced.
  12. nola mike

    2011 Tahoe Mer 4.3 - engine miss firing

    Also if only when fuel is low there could be a break in the pick up tube
  13. nola mike

    Mercruiser head gasket replacement

    There are other causes of water in the oil
  14. nola mike

    Stupid me, no oil

    Had been running great and been working very hard over the last week. Yesterday did a few hours of water sports (the kid did his first deep water slalom start and old dad managed to get a turn as well), then went on a fully loaded ride. Noticed oil pressure bouncing around 50 (usually around...
  15. nola mike

    Alpha gen 1 shift cable adjustment.. cannot get reverse.

    Have you looked at @achris video? One of the few that show you how to measure the tolerances. Also the actual service manual is pretty detailed. That clymer isn't the correct procedure. Also Reading initial post, did you raise the cable in the bracket slot? That's the initial adjustment if it...
  16. nola mike

    Mercruiser 3.0 TKS - Hard to start when semi-cold

    The point is that you have either a spring coil/choke OR a TKS module. They are completely different and don't co exist.
  17. nola mike

    Shift Lever Question

    It's DIY for me, but not for my wife. Many on this site DIY full restorations, so...
  18. nola mike

    Time for my first bellow change, tips?

    You pull the bell housing to change the cable?
  19. nola mike

    Time for my first bellow change, tips?

    The boot is the only seal entering the transom
  20. nola mike

    Time for my first bellow change, tips?

    Fair point, I have a tube on mine so didn't try.
Top