Search results

  1. alldodge

    VP 5.7 gsi - Temperature Rising

    If motor was running you should see exhaust coming out of the drive.
  2. alldodge

    Thru hull raw water inlet for Penta 275

    Go fast boats use thru hull pickups often. So long as you install it correctly should be no issues. Would also need to block off or divert I believe yhou can still get the fittings your looking for @Scott Danforth can advise
  3. alldodge

    Wont fire on plugs

    Which 3.0 do you have You mention Wht/Grn wire so I'm thinking TB4 or 5
  4. alldodge

    MC-1 Drive Dog failure?

    The first part of your post leads me thinking the lower shift cable needed to be replaced before this happened Checking the lube would be a good thing
  5. alldodge

    Threaded hole in the top of my 3.0 XL

    Most all older blocks can have a hole not used, main reason is something was attached which now is no longer needed. Might have been a hose clamp
  6. alldodge

    4.3GXI-E Excessive fuel consumption continued....

    Have you checked and compared compression numbers? Compare color of plugs
  7. alldodge

    Mercruiser 3.0 1987 engine not running well after warmed up

    Might be a fuel pressure issue (pump or fuel lines) but when was the last time the carb was cleaned? Have you checked the points and the dwell
  8. alldodge

    Bravo3 x Shaft Not Fully Seating in New MerCruiser 6.2 Coupler — Normal or Problem?

    Welcome and that's normal. Drive shaft is seated correctly
  9. alldodge

    Bravo 2 input shaft won't barely turn but propeller turns fine?

    So you can see the upper shaft turn by rotating the prop, or spinning what? The drive shaft is seized, it should turn easy by hand Maybe the drive shaft roller bearings
  10. alldodge

    5.8l efi idles too fast

    The first pic reminds me of wires that would be attached to an Alternator The second pic the black plug reminds me of fuel injector plug, and the white connector would plug into it. Don't know of any motor requiring that type connector to be removed So far as the plug to cap wires, so long as...
  11. alldodge

    Which NMEA2000 gateway to use on a VP 4.3 GXi-E

    SN 4012137867 Using this serial number it comes up with more detailed info. ECM part number 3863326 Volvo Gateway
  12. alldodge

    VP 5.7 gsi - Temperature Rising

    The number isn't coming up at https://www.volvopenta.com/shop/0 Look in the pump housing with impeller removed and do you see any wear marks?
  13. alldodge

    Which NMEA2000 gateway to use on a VP 4.3 GXi-E

    Welcome Your serial number (tanks for providing) list part number 3858888 which is a MEFI but unsure if it's a 3 or 4 model. Either way you will need a gateway connection to use. MEFI's are not great with providing much data and if the gateway's that are available work, I'm unsure. Suggest...
  14. alldodge

    VP 5.7 gsi - Temperature Rising

    VP so you have a crank driven water pump, correct? Have a serial number? Are their any grooves on the wear plate or pump housing?
  15. alldodge

    Vapor Lock

    Agree, VL is not magic that just happens
  16. alldodge

    Fuel tank size

    Welcome Wake Boarding Mag list it at 40 gal
  17. alldodge

    Raw water pump

  18. alldodge

    Mercruiser MPI 5.0L w/ Bravo 3 outdrive not going into gear... lower shift cable is very hard to shift

    FunTimes has you covered pretty well The drive should shift easy with your hands holding lower shift cable and motor running on a trailer. Remove cable from shift plate, start motor and an easy push/pull will change it F/N/R
  19. alldodge

    Raw water pump

    Either the pump is defective or bolts/washers not installed correctly
  20. alldodge

    1972 mercruiser 120 hp

    One that fits on the drive We need type of boat, what prop is on it now, what is WOT rpm now
Top