Search results

  1. A

    Leak thru the lower aluminum anode bolt, I recently installed them after redoing transom. Do you put silicone around the bolt prior to tightening?

    I never use silicone due to the fact that once you use it, nothing else will ever stick there. And it doesn't last, especially below the water line. Plenty of other better quality products...
  2. A

    Process for changing boat trailers?

    Nothing beats practice....first time backing up for the season is always a tough one. I learned to backup a trailer at age 13, now 74....lots of practice!!
  3. A

    1993 Evinrude 9.9 - no spark

    Get your hands on a factory service manual and all the info will become much easier to find.
  4. A

    Lucky Day

    Way back in my much younger days while driving clunker cars, I always carried a hammer and a roll of duct tape ! Used them often !
  5. A

    Process for changing boat trailers?

    I don't see any difference backing up with my 12" extension in place....I have to backup over 300 ft to reach my barn door from the road thru a big S curve around the garage. Can't notice any difference, but have not tried the 24" extension!!
  6. A

    Shoreland'r Rebuild

    That is a rebuild/ repaint from the ground up ! Nice !
  7. A

    Gas leaking out of one carb?

    Get rebuild kits and rebuild them correctly ! Just cleaning does not work well very often.
  8. A

    2014 Shorelandr Tail Light Connector Issue

    On ocassion,,I take a day and go to the local junk yard on there special days where you get your own stuff. Walk around with a pair of side cuts and snip off a couple pockets filled with connectors. Often times no charge !!
  9. A

    Lucky Day

    If duct tape won't fix it, you need a hammer !
  10. A

    Outboard motor upgrade?

    Gotta be a big drag on a deck boat hull, I was referring to two smaller (narrower) V bottom hulls to create lift and less drag
  11. A

    Setting rpm on 3.0 mercruiser

    All marine engine mfgrs state to adjust idle speed and idle mixture adjustment if applicable while underway, in the water, not on muffs or in a barrel. Your call whether to follow instructions or do your own method..
  12. A

    Outboard motor upgrade?

    Often wondered why toon mfgrs don't form the toons into a planing type hull?
  13. A

    Process for changing boat trailers?

    I have the same issue with shallow water ramps. I used a 24" extension just for launching the boat, then removed it for highway travel. Then tried a 12" extension and that works well at the one ramp I mostly use. The 12" extension causes no issues towing other than some extra rattles, but no...
  14. A

    Opening day of summer boating season.

    A friend of the family has a go fast boat with twin 454 V8 engines...his total fuel capacity is over 300 gallons....sure glad I don't have to fill them !!
  15. A

    Dust Cap Woes

    Good possibility...Check hubs after 10 miles or so, should be warm but not hot or uncomfortable to touch
  16. A

    Bilge pump wiring backwards?

    And lean in close and get a good look at the outlet port when you connect the wires, you will see if it works ! Couldn't help that thought when I read your post, might make a funny story.....
  17. A

    25 HP 4 stroke vs 40 HP 2 stroke???

    Can't speak for the new models, but neighbor has a Honda 4 stroke that is only barely quieter than my Merc classic. At wot we can carry on a conversion without yelling on either boat. Unless new motors are different, I don't see much difference.
  18. A

    Depth sounders and Old transducers

    Transducers need to match the head unit specifically, not a universal fit type thing.
  19. A

    Shift Lever Question

    If you really have all those abilities, then you should have already researched the issue with your make and model of your motor and knew if you had the ability to service it.
  20. A

    Leak in aluminum boat

    From my research it is not long lasting and can be very difficult to remove. Hope it works for you.
Top