Search results

  1. jerryjerry05

    Throttle cable maintenance and adjust basics? Force 85 H.P. or other..

    The first 4 posts in this forum have tips and procedures for the Force motors. Some of the links don't open but the next one might? U=tube videos by FrankA look them up. Franks was pretty good at his repairs and video's but some of them don't open.
  2. jerryjerry05

    Dont know what model i have

    Ask in the Mercury forum??? This is the Force/Chrysler forum.
  3. jerryjerry05

    Needle valve seats availability?

    Post a close up pic of the needle. The needle/seat: they come two ways. #1 the seat has a tiny o-ring (might be found at Granger)and a solid needle. #2 the seat is solid brass and the needle has a soft rubber tip. Is that seat removable? It doesn't really look like it. Some are pressed in and...
  4. jerryjerry05

    89 force 50 lift ring

    Cheapo tools= crappy results. The 1/4=20 threads already cut into the flywheel, often times they pull out as soon as you apply pressure. Tapping to the next size makes a big difference. One thing I found was using a torch and apply heat direct to the crankshaft end. Then a 3# hammer on the puller.
  5. jerryjerry05

    The saga continues

    Check the trigger leads, they are VERY THIN and break under the shrink wrap, do the tug test and see if the lead pulls out of the connector??? #3 operates the fuel pump, check the diaphragm?? A "New" pack can be bad right out of the box. A stator can test good and still fail.
  6. jerryjerry05

    85 hp force outboard no spark

    85/125 Kill switch's?? They didn't come with a kill switch (KS) on the motor. If it had a KS it usually came on the dash and had a cord and plug. The later years the KS came on the shifter (Mercury) outboardignitiondotcom has some tests for the components they sell. Testing the packs: no set...
  7. jerryjerry05

    97 ish 15 hp force cowl filling with water

    Thanks.
  8. jerryjerry05

    1966 6HP Chrysler Model 6601-02-03 - looking for parts

    Pictures would help? unfortunately you can't add pics until you have 5 posts :( Picture sharing sites will help add pics.
  9. jerryjerry05

    1991 force 150 hp water pump replacement

    WATER PUMP KIT FK1204-1 Most times all you need is an impeller IMPELLER-Water Pump F694065 about 35$ This site sells parts. From the part#...
  10. jerryjerry05

    Tips for Re-Installing a Flywheel?

    A spot of superglue?
  11. jerryjerry05

    Help with 1974 chrysler 1057hf

    Nordin usually answers questions on these older motors? I don't have that much experience on these older Chryslers.
  12. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    Bosco, none of your business what I do. You don't want to help??? then don't read any of my posts and keep your opinions to yourself. Nothing good to add?? add NOTHING!!
  13. jerryjerry05

    Help with 1974 chrysler 1057hf

    The following links are for some repair/tests. They might work on your setup?? https://www.outboardignition.com/support/115-3301.pdf / Powerpack https://www.outboardignition.com/support/155-1450.pdf / Rectifier https://www.outboardignition.com/support/182-5475.pdf /Coil...
  14. jerryjerry05

    125 Force Outboard won’t achieve full power

    That might be part of the problem???
  15. jerryjerry05

    Help with 1974 chrysler 1057hf

    What ignition system?? Distributor? Magnapower? The newer ignitions(your repair page) that uses power packs and you probably don't have that system. The stator on the older systems charged the battery, the newer systems the stator gone bad could kill spark to the system. The newer system, the...
  16. jerryjerry05

    Best gasoline octane for old Chrysler Outboards

    What I would do: use the 87 with 10% Ethanol. Add Ethanol stabilizer if the boat "might" set for a while??? Otherwise I just ran pump gas, usually WallyWorld gas, and kept the tank full after using. Try t keep it out of the sun. The biggest problem was the rubber hoses melted from the Ethanol...
  17. jerryjerry05

    89 force 50 lift ring

    Took the lift ring to Home Depot. They had nothing to match the threads to. The parts list says 3/4-16 F-1968 part# It's the same for the 50-85-120 125- 150
  18. jerryjerry05

    2003 lx225 OX66 knocking sound

    Compression test? Bore scope/camera?
  19. jerryjerry05

    89 force 50 lift ring

    In have one. If you don't get an answer, I'll take it to Home Depot and get the threads measured and post on here tomorrow.
  20. jerryjerry05

    89 force 50 lift ring

    I can't find the part# for the lift ring. The 50 needs a smaller lift ring than the bigger motors. I used piece of 1 1/4x 1/8 x 4"flat stock. Drilled 2, 3/4" hole 1/2" from the end and then bent it 90d. Then removed the flywheel nut, installed the new lift bracket, replaced the nut, then lifted...
Top