Search results

  1. jerryjerry05

    Lower Engine Mount/Shock advice

    The difference is probably the paint??? Ones blue the older is white??
  2. jerryjerry05

    Alpha One Gen 2 Outdrive not going back on

    YEA!!! I used an assortment of 2x10x12 blocks and just built them up to the right height. Left the Cobra in either gear f/r, it changes gear to N when it slides all the way in.
  3. jerryjerry05

    Gimbal Bearing Compatibility and Source?

    60794A4 early# 30-879194A02 superseded Just make sure you get OEM Installing, it shouldn't be real hard to install if you have the right tools. Make sure the hole is spotless and when inserting, perfectly straight. Align the grease hole too...
  4. jerryjerry05

    Volvo Penta AQ140 water coming out of carbs.

    The 140 is 125hp 1975-79 The 130 is 110hp 1975-77 Should be an easy swap. If you drop to the 130 make sure you use the Volvo prop. They just work better.
  5. jerryjerry05

    Looking to buy a 1976 starcraft holiday 21 ft. With a 165 6 cylinder engine. Engine is locked up,and was wondering if possible to rebuild that engine?

    It's a Mercruiser drive. Did a lot of Walleye fishing out of a 21 Islander. Try to get it unstuck before you buy any parts. Sometimes a couple days soak in MMO (marvel mystery oil) will help free the pistons. Worst case, remove the head, 4x4 and a 8# hammer. Start in the second and then the 5th...
  6. jerryjerry05

    Alpha One Gen 2 Outdrive not going back on

    First your in the wrong section! Find the Mercruiser repairs a little further down the page. Second, the o-rings on the shaft, remove them and clean the grease from the groove. Then reinstall and grease only the top of the o-ring. Too much grease under the o-ring lifts the ring and makes it...
  7. jerryjerry05

    Idling

    If the tanks full and not in direct sunlight. The gas should be usable.
  8. jerryjerry05

    Water in cylinders

    Time for a new boat. Gonna refinance the house and get a NEW boat!!
  9. jerryjerry05

    Force 125 1988 Water drains out the exhaust

    When using the hose direct to the copper tube, the regular house pressure isn't enough(most cases) to activate the pressure release. The impeller/pump can pump a LOTTTT of water, usually more than the hose can produce and in the water you have access to millions of gallons and the hose comes no...
  10. jerryjerry05

    Water in cylinders

    Thanks
  11. jerryjerry05

    Water in cylinders

    Thanks, head gaskets replaced this year.
  12. jerryjerry05

    Water in cylinders

    1986 200hp Starts and runs then gets water in the 3 cyl on the right(maybe the left???) That's all the info the owner told me. ????
  13. jerryjerry05

    88 Johnson SPL - lower unit oil color

    That's NOT right, it shows it has water in it. Drop the lower unit and then do a pressure test.
  14. jerryjerry05

    Force 125 1988 Water drains out the exhaust

    Thank goodness you asked before tearing things apart!!! You might not EVER see water coming from the 2 holes in the mid section. Those are for excess pressure release. Like Nordin said most water goes out with the exhaust. Depending on the muffs?? you might need to use duct tape when you run the...
  15. jerryjerry05

    Twin 150 Fichts won't rev past 2500

    What should the pressure on the pump be? Gonna get the factory manual, they(EBAY) have some for 1996/97 will they work for a 2000 150 Or where can I get the right one? Thanks
  16. jerryjerry05

    Twin 150 Fichts won't rev past 2500

    Gonna check pressures in the AM But both motors throwing a check engine light? Gonna try to get codes then too. Thanks for the suggestions.
  17. jerryjerry05

    Twin 150 Fichts won't rev past 2500

    Yes we primed the oil system. New hoses, new squeezies and primed the system. Thanks.
  18. jerryjerry05

    Twin 150 Fichts won't rev past 2500

    Twin 150 Evinrude Ficht. Starboard starts and idles fair. Good compression. The port doesn't want to idle well at all unless the balls squeezed. The check engine light comes on both motors and won't rev past 2500 rpm. New hoses/squeeze balls and cleaned oil tanks new squeezies. What would cause...
  19. jerryjerry05

    88 50 hp Force No Spark

    You check for spark on BOTH plugs? You use the choke? I saw the second video abut the pump and impeller. Look up a parts diagram and see how it is to replace the water tube. If the homemade fix worked before?? then use it. The tube can be pulled out and a new one stuck back in, unless the...
  20. jerryjerry05

    1995 yamaha 200hp v6 2 stroke txrt spanner nut 6g5-5483-00 and claw

    outboard spanner nut?? what's it used on? Pics??
Top