Search results

  1. jerryjerry05

    2005 90hp Yam no spark.

    COIL, PULSER 6H0-85580-01-00 This motor uses a coil, pulser.(bosco99) Any idea how to test it? What's the specs? or where can I find them??? Thanks
  2. jerryjerry05

    2005 90hp Yam no spark.

    This is what I printed. Says Trigger tests??? For an older motor. Read from Read to OEM Reading CDI Reading DVA (connected to pack) White/Red Trigger wire White/Yellow Trigger wire 280-430 ohms 280-430 ohms 2.5 Volts Minimum White/Black Trigger wire White/Green Trigger wire 280-430 ohms 280-430...
  3. jerryjerry05

    Motor stalls in neutral

    Maybe adjust the neutral safety switch? 2 TINY allen headed screws.
  4. jerryjerry05

    Hi all so back kind of after a rebuild as found broken rings not causing any problems but once seen

    Missing on 3-4 Try swapping the packs, check the grounds. I have a #12 wire about 14" long with alligator clips that I use as a temporary ground .
  5. jerryjerry05

    Merc/force 120 mods need help.

    What's a reed stuffer??? Look up all the posts by FrankA. Frank Amphora he did a lot of mods to these Force and Chrysler outboards. Look for his u-tube video's too. He did posts on porting and polishing and boring. IF?? my memories right(maybe? maybe not?) The 99. It was originally a 125...
  6. jerryjerry05

    2005 90hp Yam no spark.

    I printed the test procedures for the ignition system. Stator/trigger etc.
  7. jerryjerry05

    2005 90hp Yam no spark.

    2005 90TLRD 1017108 Guy calls and says his motor has no spark. What's the first thing I should be looking for? I haven't looked at it yet, probably tomorrow. I have a DVA Thanks
  8. jerryjerry05

    Hi all so back kind of after a rebuild as found broken rings not causing any problems but once seen

    Your post didn't make much sense?? Is your motor missing on #3 and 4? Use a good spark tester: Missing both on 3/4 sounds like the pack might be bad? Try swapping them around and see if #1/2 start missing? IF?? #3 or #4 is missing check the trigger leads, they are very thin and break under the...
  9. jerryjerry05

    125 Force Outboard won’t achieve full power

    Like racerone said maybe running on 3 cyl. Spark test each cylinder. Always list compression numbers. Then do the starting fluid test: start motor, spray sf around the intake side, including the 4 port covers and around the carbs, etc. if the spray makes the motor run different then it's sucking...
  10. jerryjerry05

    Chrysler 75 hp. Difference in spacer plate to same motor?

    Most cases the poppet gets stuck and stops working. Years ago I was told by the Force techs that it can be removed without any adverse affects. They stopped using them around 89/90
  11. jerryjerry05

    Chrysler lower unit rebuild

    Some seals can be installed using the wheel bearing race tool or a universal joint tool. Like Racerone suggested the socket of the right size. I sometimes use a BIG C-clamp. Just make sure the surfaces is clean and the sealer coats the mating surfaces. The shift rod seal: if the surface isn't...
  12. jerryjerry05

    Chrysler 75 hp Distributor cap gasket?

    F14020-1 Can be found on Ebay from $7.25 to $30 Ebay # 173114838757 is the cheapest one. But you can run without it. It is a moisture seal and should be used.
  13. jerryjerry05

    150 Evinrude Ficht 2004

    Thanks
  14. jerryjerry05

    150 Evinrude Ficht 2004

    Thanks, New fuel lines, port motor=removed vapor sep. and cleaned it. New impellers both motors. New fuel lines and filters. Comp great, both motors. New oil lines and tanks cleaned. The boot strap tool? why would I buy that?
  15. jerryjerry05

    1977 Chrysler 10hp 100HA cowling

    Look for marine salvage yards. Antique outboards. There are yards all over the mid west. Here's one: https://forums.iboats.com/threads/salvage-yards-by-wilde1-verified.428012/ Hope it works Another one: https://www.facebook.com/groups/1739059919642568/
  16. jerryjerry05

    1956 Johnson 30 / Starter won’t turn flywheel completely

    Do a compression test? Dirty inside starter? Does the starter get hot? how about the battery posts and cables? If the bearings are corroded, that can cause hard turning too.
  17. jerryjerry05

    150 Evinrude Ficht 2004

    Twin 150 Ficht, both only go to 2500 and then cut out. Any suggestions or ideas? Any other repair forums or places ? The only place in the treasure coast area keeps putting the owner off, first appointment was Jan 10 then next week and again next week. ANY HELP would be appreciated. The owner...
  18. jerryjerry05

    1995 Force 50 Turns over, doesn’t start

    If your running in a tank? Make sure the water is deep. Needs to be 4 inches over the top of the cavitation plate. FYI If it's a 2 piece lower: then it needs special muffs for running on the hose. Using regular muffs can cause over heating.
  19. jerryjerry05

    1989/1990 4.3 distributor

    I put a piece of sponge with WD under the inner plate. Ten WD Silicone spray the housing Then replace every fall when winterizing.
  20. jerryjerry05

    1988 mercruiser alpha one water pump issue

    The direction of the vanes?? makes no difference. The impeller is it the same as the one you removed? They sell one(Force/Chrysler) that is just about the same size and when installed it pumps but pumps poorly. On the hose or in the water?? The hose might not supply enough water?? You replace...
Top