Search results

  1. alldodge

    LiFePO Batteries ???

    You know better then I but, if one goes bad most likely you won't see it coming and it doesn't take long for one to take the other out
  2. alldodge

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    No, run in/out with no issues Might have issues reattaching drive, but connect long side then push down until short side lines up Don't fully understand the comment, but in most cases it's not good to fix issues with everything back together
  3. alldodge

    1976 Starcraft Mariner 21' Layout Changes? (v2)

    Is it you can only reach 4000 rpm then it would be over propped which would lug the motor. If your just cruising at 4000 then this would not be an issue. I hardly ever go above 4000 and can go as high as 6000
  4. alldodge

    How to add fluid to a 150 Yamaha hydraulic steering?

    If you don't see the plug then see if it has a cover all around the back of the helm that may come off
  5. alldodge

    Evinrude 15hp 15804B 1978 Complete rebuild 3x over bore

    Look up lock wire Need thin wire to clean the channels out Nice looking motor
  6. alldodge

    Mercury ob 1995 40hp. Roll pin with Trigger assembly??

    Don't have a manual for your motor but have another which uses a trigger link rod. This rod is adjusted in/out to set timing. Motor is shut down each time to readjust. Maybe yours has something similar
  7. alldodge

    How to add fluid to a 150 Yamaha hydraulic steering?

    Welcome Is it a Yam specific steering system or something like seastar? What year is the boat? Normal is bleed/added at the HELM
  8. alldodge

    2006 DP-SM with Clicking Under Load

    I believe it's the U joints Being certified just explain symptoms to them and they will probably come to the same
  9. alldodge

    Tilt/trim pump

    Welcome In most cases, it needs to have the problem to find it My guess is something is getting warm and loosing contact including the grounds. Many don't look closely at the grounds but that is the other half of the connection. Could be the switch in the handle, mine went bad A test light...
  10. alldodge

    Help to source Bravo 3 gimbal housing

    Finding just the Gimbal housing is going to be tough. Post in Offshore Only wanted classified area, there are a few there that have all kinds of parts This is cheapest one found on ebay https://www.ebay.com/itm/275490064918?chn=ps&srsltid=AfmBOor57Fsz4iqTwiRieA7dtgkzaG_1jPBlxa7aK1sxTOX1KBw7RcHknO4
  11. alldodge

    Throttle Control Button, need a replacement

    Most likely not going to find one and need to replace the control.Might be able to find one HERE that will work
  12. alldodge

    1976 Starcraft Mariner 21' Layout Changes? (v2)

    Done
  13. alldodge

    1976 Starcraft Mariner 21' Layout Changes? (v2)

    You could get many more comments it the restro area. If you like I'll move it
  14. alldodge

    hi there :)

    ^^^ Increase that point count
  15. alldodge

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    Never "assume" anything Also if you go from one brand to another you also might need to change controls, cables and fuel lines
  16. alldodge

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    Same test different term used
  17. alldodge

    hi there :)

    Welcome
  18. alldodge

    Upgrade Tracker trolling motor from 12v to 24v

    Welcome John For the most part wire is wire and it doesn't care if it has 12 or 24V. What does make a difference is the amount of current (Amps). Determine what size (gauge) wire feed motor now. What size fuse is on the motor. Look for specs on current motor and see max amp draw and should...
  19. alldodge

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    Any can do it To do a compression test, pull plugs and attach Compression gauge Open throttle wide open and crank motor over at least 4 times and record reading. Remove gauge and move to next cylinder and repeat until all have been tested Remove drain plug slightly just enough to see if any...
  20. alldodge

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    Agree
Top