Search results

  1. alldodge

    Volvo penta 2 pin alternator wiring ?

    Should be same as Delco style middle row far right https://bpi.ebasicpower.com/charge/alternatorwiring.htm
  2. alldodge

    No power at coil: Volvo Penta 3.0

    Was unable to find a GSP"A" but was able to find the B version and I'm seeing EST ignition. Is yours carb or EFI?
  3. alldodge

    Solas stainless 4 blades all the same?

    Have not used a Solas but with your 3 blade (B) 19 pitch (P) hitting the rev limiter you do need more pitch or more blades. A 4B 19P is equivalent to a 3B 21P Either of the above will reduce your WOT rpm but also reduce your hole shot. If you go with a 4B 17P will increase hole shot, will...
  4. alldodge

    SAE j1171 trim motor. Pressurized air in reservoir. Leg falling slowly

    In most cases it's the cylinders that need new seals. Rebuild kits can be found and easy enough to do
  5. alldodge

    8.1 GXI-J Cranks but No Start w/ Diacom Logs

    The way I read it, the motor will start and it's not stalling so the CMP is not lost. The motor does run but doesn't run very well and with both CMP and CKP codes, I would lean toward the CKP. Wrote this down from @muc posting on the J model and testing CMP [[ How to check CMP (cam position...
  6. alldodge

    Rear view Mirror

    That's looks same size as I had on my cruiser. Could put it next to center support pole, but maybe on the hard top post. My main concern is this boat already has a lot of blind spots, so adding another is the issue. Further away and higher would be better but wonder if it will give enough...
  7. alldodge

    1988 4.3 omc wont start

    Welcome Agree with Bondo Adding good gas to bad gas just gives you more bad gas. Could be the fuel filter is full of water and or crud
  8. alldodge

    Trim problems

  9. alldodge

    Trim problems

    All good but a Solenoid has a coil and some kind of plunger that is moved. Like a starter solenoid that moves to engage gear into flywheel A relay has a coil that moves a plunger to make electrical contact to pass power to a higher current device
  10. alldodge

    2000 Mercruiser 5.0 Thunderbolt 5 Ignition idle issue.

    Welcome Sounds like the oil pressure switch but could use motor serial number Motor cranks and during this time the fuel pump runs with power coming from starter. Once motor starts connection is removed from the starter and oil pressure builds. The oil pressure switch "should" now send power...
  11. alldodge

    Impeller ?

    Welcome Search for Volvo Penta 3843949
  12. alldodge

    Trim problems

    Assuming it use to work fine and this just started? If this is the case it's most likely in the control switch, but first, do you have 2 relays of just 1
  13. alldodge

    Volvo 2009 8.1GXI Hard Start

    And same method can be done with any wire/cable
  14. alldodge

    Volvo 2009 8.1GXI Hard Start

    Take a digital voltmeter and connect + probe on the Pos bat terminal. Connect the - probe on the starter post. Crank the motor and see how much voltage your read. Should not be more then 0.5V Can also do this with a load tester so it can give you more time to read the meter, or disconnect...
  15. alldodge

    Volvo 2009 8.1GXI Hard Start

    If Bats test good it could have a bad connection in the Bat cable it self. Sometimes the cable lug builds corrosion inside between the wire and lug
  16. alldodge

    Rear view Mirror

    Looking for a rear view mirror for the boat. Had one on the cruiser which was 4 x 8 I think and did ok. Thinking about the 2.5 x 8 but never tried one. Last thing I need is more blind spots looking forward with current boat. Could Mount off the hard top supports but not sure how much or...
  17. alldodge

    1998 Bayliner Capri 2050SS 5.7l

    Most kill switches have 3 to 4 prongs so it can be used in either ON or OFF when lanyard is pulled. https://www.walmart.com/ip/Seachoice-Universal-Boat-Kill-Switch-Kit/32738296?wmlspartner=wlpa&selectedSellerId=14649 The Mercury ones have only 2 wires and are OFF when pulled...
  18. alldodge

    Intake 496 Magnum 2007

    Welcome Always is better to let use know the motor serial number so we can find the exact configuration Using 0M687 to 0W059 is showing there is only 1 muffler and the other is open https://www.mercruiserparts.com/bam/subassembly/31816/11414/70
  19. alldodge

    Need thoughts from the car gurus

    I'm not going to buy a DI motor unless I would have to. Read up on what is required and ho to, but that's it. No water down the intake for these motors
  20. alldodge

    VesselView Link stopped reporting fuel levels

    Do you have smratcraft vessel view? If so use the setup wizard If not need to find the simrad manual for it to see how to get to size
Top