Search results

  1. K

    Trim Pump Leaking

    Just cycle the system as you said. Power trim or power steering fluid does not foam like transmission fluid.
  2. K

    Please help ....

    If you can separate the universal joint at the forward connection then you may be able to use a slide hammer to remove the female splined section. with a hooked tool pull the rear seal then with some snap ring pliers remove the rings. The shaft is threaded so that a slide hammer can be used to...
  3. K

    Super stuck gimbal bearing in Mercruiser Pre-Alpha -- is there a clip?

    Clean out the area inside the gimbal housing and take a picture then post it.
  4. K

    How to replace a VP 250

    If it is what it is described as then you should go for it. You should also also order along with the drive shaft bellows, Sierra# 18-2778 water hose connection #18-2775 molded hose. The drive shaft bellows can be replaced by just removing the upper gear box. That way you can check...
  5. K

    Mating Engine to Mercrusier problem

    In the Sierra catalog # 18-2172 engine coupler; replaces 14505a2. Used when replacing V6-V8 2 piece rear main seal with 3-1/2” crankshaft bolt pattern to a newer 1 piece rear main seal engine with 3” bolt pattern. Kit comes with mounting hardware.
  6. K

    2001 VP 5.7 GSI PEFS no start

    When you turn the key on, without turning to the start position, does the fuel pumps prime for the 2-3 seconds?
  7. K

    How to replace a VP 250

    For your lower gearcase to crack then it must have had water in where oil is supposed to be. The drive probably was all rusted internally already. If you find a complete drive just swapping the upper and lower to the mid section would also be easy. Sierra# 18-2597 Upper “O” rings. Sierra#...
  8. K

    How to replace a VP 250

    I never tried it but if he swaps the suspension fork the entire 290 would bolt up. I would only stay with a single propeller model. The main thing is the gear ratio. It has to be a 1;6 to 1. Sierra # 18-3888 lower seal kit is all that is needed to mate any Volvo model lower to the mid...
  9. K

    2001 VP 5.7 GSI PEFS no start

    I bet that the crankshaft is rotating at the required speed but the signal is coming from camshaft speed since the rpm readout is low. Are the signal pick ups in the same place as the original engine? Of course this is just a guess. Maybe someone can post a wiring diagram of your model.
  10. K

    NEW Transom seal BAD!!!

    If it was a genuine OMC boot there will be a part# on it. It was probably Asian. I agree it could have been on a shelf for many years if it does have the OMC # A genuine OMC boot can be replaced without pulling the drive with some liquid soap to slide it over the drive and not tear. .
  11. K

    Aq130 help on replacing thermostat

    Is the engine overheating? The oil cooler is easy to remove and clean, you will need new “O”rings. If the pipes in the picture are not leaking leave them alone. Sierra part #s for the copper pipes if you want them. 18-0606 copper pipe seals 18-3890 oil cooler seals. 18-3539 thermostat
  12. K

    Stumped. OMC 235 HP I/O

    These are the part#s you need from Sierra. 18-3386 water pump kit 18-3731. Locknut 18-2185 water pump shaft 18-2667 upper seal kit 18-2183 pinion shaft 18-7198 “O” ring. Qty 2 of If you have a vise mount the case with the quadrant gear. Remove the 4 stainless bolts and remove the...
  13. K

    1978 Starcraft Holiday 18 I/O steering issue

    The quadrant gear is the gear that is attached to the upper gear housing for lifting the drive.
  14. K

    Aq130 help on replacing thermostat

    Are you talking about a fresh water cooled over head cam engine?
  15. K

    Water Pump Question - Alpha 1 w/Closed Cooling

    I have had similar situations and was able to route the water with some creative plumbing using some hard drawn copper pipe elbows sweated together from the hardware store. Glad Shawn could help he always came through for me and Marine Power are good people to deal with. I purchased quite a few...
  16. K

    1978 Starcraft Holiday 18 I/O steering issue

    The exhaust housing he should have is more stream lined than the one with the screen. However the marks are just rear of the rear vertical mounting bolt and there is a oblong slot that the bolt is in for left to right adjustment. You can try loosening the 2 mounting bolts and moving the tab...
  17. K

    Ballast resistor? why

    It appears from what you are describing you actually have a electric shift model not a 800. The resistor you are describing on the starter is actually a fuse. The epoxy is a sealant. There also should be one on the alternator. You can get what is called a fuseable link from NAPA in various...
  18. K

    Trim Pump Leaking

    It may only a leaking “O” ring that seals the pump to the reservoir.
  19. K

    Water Pump Question - Alpha 1 w/Closed Cooling

    Call Marine Power 985 386 2081. They will be able to answer your question and should have what you need. Ask for Shawn, tell him I told you to call.
  20. K

    1978 Starcraft Holiday 18 I/O steering issue

    Look at the rear of the exhaust outlet where it contacts the rear of the drive just above the bolt that mounts it.
Top