Search results

  1. alldodge

    The engine stalled and no start while on the water

    What ignition system does it have? Have you check the kill switch? When key is tuned ON is there 12V on the + side of the coil?
  2. alldodge

    PLEASE HELP... I'm at a loss of what to do!

    Look on top the motor for a serial number. It will be a number, probably 0, then a Letter, then 6 more numbers Exp: 0W123456. Take a pic of the motor and post it I'm also in KY
  3. alldodge

    Stalled while idling now it cranks but no star or sparks

    2 poles, are they the ones on the back of the 50 amp breaker? Have 12V on the main starter post?
  4. alldodge

    Merc Quicksilver Gen 2 Kill Switch

    Doesn't matter its a reg switch
  5. alldodge

    Stalled while idling now it cranks but no star or sparks

    Try to retrace your steps, maybe something was disconnected Other wise trace 12V from the key to the coil with key on
  6. alldodge

    Not getting a spark boat will not start

    Its normally either on the shifter or next to it. The kill switch is required on all small boats for many years. It would have a teather cord attached to it and the other is on the driver incase they get thrown overboard Your boat might not have one since your asking
  7. alldodge

    Merc Quicksilver Gen 2 Kill Switch

    Yes, that is the kill switch Need to know if you have a 2 cycle or 4 cycle motor. The 2 cycle grounds the magneto to kill the motor, the 4 disconnects power Note the kill switch for this 2 cycle setup. Its connected to Magneto and to ground
  8. alldodge

    Alpha One-g1. Shift problem when Tilted

    If I'm understanding you correctly This is the lower and the shift foot is facing directly FOR and AFT , good This is the upper and its not facing direct FOR and AFT The cable needs to be adjusted some more
  9. alldodge

    Merc Quicksilver Gen 2 Kill Switch

    Measure the continuity of the switch action. The 4000 comes in a few styles and has 2 different switches. One for outboard (2 cycle closes when activated) and one for I/O (opens when activated)
  10. alldodge

    5.0gi to 5.7 swap

    Don't listen to the shop, and as Bondo mentioned don't change the cam. You will need the ECM reflashed which isn't hard, just need the right software like MEFI Burn. With this software and the right Bin file its a easy swap Could contact Bob at OBD Diagnostics or a member on Offshore only...
  11. alldodge

    2002 Volvo penta Gxi 5.0 beeping issue

    I'm unable to verify Ac 213-96 is for your motor. It comes up 1996 and older, so pre vortec This one comes up as vortec and also Merc and VP. Not saying yours is not correct, or that this will fix the issue, just not able to verify the part...
  12. alldodge

    Won’t stay running

    Put your meter on each side of the diode and measure resistance, being open it should read infinite resistance. A good diode will read low with leads on in one direction and by swapping leads it will read high
  13. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Disconnect solar, turn something ON for each Bat for even 1 minute and see if it stays up
  14. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    I like to see 14.5V with motor running and 12.7V after sitting for an hour or so
  15. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Wish I had something but there isn't much for CAT motors yet Might have something to do with your solar hook up
  16. alldodge

    Stalled while idling now it cranks but no star or sparks

    Crossing fingers In that case you might have break before make switches, and they should never be switched when a motor is running
  17. alldodge

    Not getting a spark boat will not start

    Looks like carb motor Your kill switch flipped OFF maybe?
  18. alldodge

    Stalled while idling now it cranks but no star or sparks

    The key powers up the ECM and MPR. If they don't get power, nothing works Fuses and relays.
  19. alldodge

    Won’t stay running

    Yes you can check it with just resistance. If you get zero ohms then its open and from your problem that is what the issue is Yes, if the diode opens its like cutting the wire.
  20. alldodge

    Stalled while idling now it cranks but no star or sparks

    ok, if you have Bat switches that make connection before breaking connection there is no issue. If they break before Make then a ALT may have fired. If ALT spiked it could have taken out the ECM. Hope the worst might have blown a fuse Need to find out if the cables are still connected to the...
Top