Search results

  1. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Found some more info but this list 2006 and on
  2. alldodge

    I am a Pawpaw!!!! :)

    Congrats
  3. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    The first part of the manual talks about a harness that is not using smartcraft but is ready (so to speak). This continues how to wire thru page 34. Shows if junction boxes are there but not being used so weather cap is all that is needed. Connector M on page 4 is needed if that type of cable...
  4. alldodge

    New Engine Replacement - Engine Died and Hydro locked after 5 hrs!?

    Need to find out the moisture reading before anything else. If hull is full of water or wood is soaked then your dead in the water. The higher risers will help but may not be enough What were the holes in the hatch used for? You could probably cut them off for clearance. Then get a piece of...
  5. alldodge

    Rinker differences

    The 236 was Rinkers first try into the entry level go-fast boats. The cuddy is smaller (not as tall). The 236 didn't go over very well so they increased the height of the cuddy and changed the seating and called it 232. 236 has 2 buckets and a single row rear seat 232 has 2 buckets and a wrap...
  6. alldodge

    A mercruiser 4.3l MPI with a low weak idle hard to start

    Think that is another puzzle is with the water pressure showing zero the available power should be less then 100%. Also I would expect to see guardian mode active
  7. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Think of the CAN buss as a hose filled with water and the terminator(s) seal the ends so the water will stay filled. If a terminator is left off then the water keeps pouring out. You can use a 4 port junction box but all ports not used must have terminators for it to work. Also with just...
  8. alldodge

    A mercruiser 4.3l MPI with a low weak idle hard to start

    What fixed the seawater sensor? What is the motor serial number? Might be the Throttle body factory adjustment has moved. Look close at the stop screw and see if it has been moved
  9. alldodge

    2006 Volvo 5.7 osi-d crank no start

    In your neck of the woods I'm thinking 91 is 87 here, should be good. The whine may have been the fuel pump having trouble pushing fuel. Usually get a hiss with intake leak and rough idle To add I would take rich anytime over lean
  10. alldodge

    2006 Volvo 5.7 osi-d crank no start

    Could be ECT sensor as tailgaters mentioned, also MAP sensor or if your running higher octane fuel then 87
  11. alldodge

    2006 Volvo 5.7 osi-d crank no start

    Did it run long enough for the motor to get up to full temp? If not then its running rich because its cold.
  12. alldodge

    Help me to find brand of this boat!

    The HIN is a USCG requirement only and looks like your on the other side of the pond, so not a requirement
  13. alldodge

    Wiring harness for 5.7GiF

    Wait not 14 it would be 12
  14. alldodge

    Wiring harness for 5.7GiF

    Edit No, it will flash once (short pause) then flash 2 times, longer pause
  15. alldodge

    Wiring harness for 5.7GiF

    MEFI code reader can be made with a 12V resistor type LED and a paper clip, or digital multimeter with tone and paper clip. Connect as shown and count the flashes with key ON and not running. Code (EDIT) 12 is all good and codes repeat 3 times then long pause and starts again
  16. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    The terminator part number is list in pics. Note there is one on the motor and one on the junction box
  17. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Don't know how to test a smartcraft gauge by it self, but they all interpret data from the CAN network. If the network is connected correctly with a terminator then it should work.
  18. alldodge

    Rec gas prices???

    Diesel Home 439, Campbellsvile Kroger 439, Louisville 4.79 (G son B ball game :D ) Filled truck on return trip at Kroger with 1.00 off so 3.39
  19. alldodge

    Breaker

    With no power on one set of breakers look for the main. This is a shore power setup
  20. alldodge

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    Great work
Top