Search results

  1. alldodge

    1987 Bayliner Capri 3.0 - ignition switch does not turn on starter

    Look for an inline fuse going to the B terminal behind the helm
  2. alldodge

    Gasket

    Manual 1 doesn't show it during build up. Parts breakdown does show in between block and plate. Seeing that the adhesive showing being affixed to plate, I would reinstall it that way. Seal goes on with raised portion facing AFT on the bottom. Then plate, then flywheel...
  3. alldodge

    Gasket

    What motor and what part is the plate (flywheel cover maybe?)
  4. alldodge

    Registration with no serial numbers

    KY doesn't require boat trailer plates, my comment stated car trailer.
  5. alldodge

    Registration with no serial numbers

    The good thing with home made (at least in KY) is what its taxed at lessor value. Says mine is worth 100 for 2 axle 18ft car trailer
  6. alldodge

    Registration with no serial numbers

    No issue hand made for me, no sherif, constable, nothing. Sent paper work in, signed off and they sent me the plate to install on my car trailer
  7. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    I use this site for VP parts, and mine is US yours should go to GB I think https://www.volvopentashop.com/epc/en-US
  8. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    Easiest way to find GM part numbers is go to a website like "GM Parts Direct", or go to place like Summit Racing and find it that way
  9. alldodge

    Wiring diagram for 5.7 GSi PEFS? Or AQ271C? Ideally both?

    Like with all threads,need to post updates or new questions otherwise we think things are ok
  10. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    I use trim down every time the boat goes in the water. Its up some while on the trailer because if it was full down it would drag on the ramp. Put in REV and when it floats off and gets a bit away from the trailer, it goes the rest of the way down So I have to retract what I said at first
  11. alldodge

    Drive lube dropping?

    If the drive has not been run much since it was replaced, I wouldn't think to much about it. If it was run a few hours and topped off, and dropped again I would look into it
  12. alldodge

    Boat won't move

    I'm thinking the splines on the coupler stripped out not moving at all
  13. alldodge

    Boat won't move

    Its running but won't move, means its either the coupler, prop hub or drive. As ding mentioned, put in gear and spin the prop. If it spins its in the drive If it doesn't, start motor and put in gear. See if the drive shaft is spinning behind the motor
  14. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    Did notice it posted as 25 but I meant 20 It says 15 so I would keep it at that Look in your shift handle to see if there is any chaffing or the wires going on
  15. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    Ok got it, that shouldn't happen If you have a manual should the fuse be 15 amp? Otherwise I don't know
  16. alldodge

    Honda BF15D will not stay running (Purchased Used)

    Impeller missing fins and temp sender broken. My first thought is the motor over heated and there is a motor issue. Don't see a temp sendor keeping any motor from running. Folks lie all the time. Honest folks get taken all the time Do a compression test
  17. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    NO expert, just a idea When in reverse the pressure is increased inside the trim cylinder so the valve that keeps the drive from coming up out of the water holds tight. The trim motor turns ON and the motor stalls because the pressure is to great Why ya trimming up in reverse?
  18. alldodge

    Remote tilt switch

    I don't have a VP 8.1 wiring diagram, but the others show it should be plug and play. This is assuming the wiring is just a parallel connection with the original switch. Is that a Red/Purple wire on the motor side?
  19. alldodge

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    If its flooding check the float adjustment as scott mentioned
  20. alldodge

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    Look good enough to run. Changing gap won't cause a non-run issue unless the coil is taking a dump. Very few coils actually go bad
Top