Search results

  1. T

    Resin Cracks

    Poly will be fine. And 1708 does have mat stitched to one side - but since it's stitched it doesn't need the styrene binder to hold it together, so epoxy will wet it out fine. Plain CSM does have the styrene binder and will not become as pliable when wet with epoxy, as it does when wet with poly.
  2. T

    My 1981 Citation Marquis...

    Honestly you may end up making more work for yourself by trying to keep as much of the old stuff there, especially the old tabbing lip. Grind it flat, install your new transom, make PB fillets, and lay new tabbing. This is the way.
  3. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Went through the starter - just needed cleaned and re-lubed. Making progress on the gunwale storage boxes - ready for glass.
  4. T

    Alpha One power steering - how to remove cable?

    I was able to get the old cable out with some lubricant and a hammer. I'll clean up the inside of the tube really good. Appreciate the input guys!
  5. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Yep, I'm buying the book and parts from him.
  6. T

    Alpha One power steering - how to remove cable?

    Thanks. How does the tube come off? Loosen this nut?
  7. T

    Alpha One power steering - how to remove cable?

    Alpha One Gen 1, engine SN 0B651656, drive SN 0B612075, transom assembly SN 0B667146 I pulled the boat apart for a full gut/restore starting last September and just set the power steering unit and cable to the side - at the time I couldn't get the cable to come out of the unit. It's time to...
  8. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Got the transom assembly bolted onto the transom today. Used bellows adhesive and painter's tape to hold the seal in place on the transom plate, then removed the tape and bolted it in. I picked up about 12 more board feet of mahogany and started making the thin trim pieces for the dash and...
  9. T

    Best Way to Lay Resin on CSM?

    I also am a fan of pouring the resin on directly and using a 4" mini paint roller to spread the resin and push it into the glass. Wrap the plastic part of your paint roller handle in blue painter's tape. The metal part you can clean with acetone but the acetone will melt the plastic handle. I...
  10. T

    1981 Sportcraft 270 repair underway - transom, stringers, & repower

    Where do you get the spare bronze plugs from? Never mind - I see that iboats also sells spares.
  11. T

    Alpha One Gen 1 transom assembly seal

    Good call!
  12. T

    Alpha One Gen 1 transom assembly seal

    Great - I'm gonna get it installed tonight!
  13. T

    Alpha One Gen 1 transom assembly seal

    Thanks. That's what I figured, but wanted to make sure.
  14. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Installed the new exhaust flaps in the exhaust pipes. It originally had rubber flaps but I went with the stainless steel flaps made for Corsa exhausts. Had to cut the old pin out (which was vertical) and weld the new pin in the horizontal plane so the counterweight will shut the upper flap...
  15. T

    Alpha One Gen 1 transom assembly seal

    I couldn't find it in the manual - I'm getting ready to install my transom assembly back onto the boat. I have a new foam rubber seal that goes in the groove all the way around the transom assembly - do I need to add any sealant to this seal besides a little bit of bellows adhesive in the...
  16. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    I glassed in the two front supports for the bench seat today. This marks the last of the structural fiberglass work! A big milestone. I spent the rest of the entire day wet sanding and buffing the transom. I wanted to do this before I started attaching things to the transom. I had to...
  17. T

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    Yeah, my street/strip car is the real money suck. 🥵 ...and my wife and daughter don't really get to enjoy it. Of course they haven't gotten to enjoy the boat yet either. 😂
  18. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    I've been somewhat slow moving the last couple of weeks. I had my overhead power lines to the house put underground to make room for a carport to park the boat under - that was an ordeal. Next, I wanted to wait to make the front supports for the bench seat until I had the speakers - I finally...
  19. T

    1981 Sportcraft 270 repair underway - transom, stringers, & repower

    It's a cloth made up of two layers of non-woven roving that total 17 oz with a 0.8 oz CSM mat stitched to the back side. Each layer of roving fibers is laid 45 degrees to the direction of the roll/stitching. Since it's not woven and since the fibers are at an angle, the fibers can more easily...
  20. T

    1981 Sportcraft 270 repair underway - transom, stringers, & repower

    To me those do look like tiny bubbles - maybe from the wood soaking some resin out of the cloth in spots where it didn't take in enough resin from the first pass. Or, it could be from not getting the mat wet enough. For big 1708 layups onto wood (big = too large to pre-wet the mat side first)...
Top