Search results

  1. jimmbo

    What to do with old 2 stroke mix

    Put it in the Mother in Laws car. Of course doing so will damage the Catalytic Converter(s), but hey it is the MIL Use it, diluted in lawnmowers
  2. jimmbo

    Camshaft specs. needed, modification feasible?

    A bit more money spent initially by getting the part from MerCruiser, which will work very well, is money well spent. All the tweaking in the world of the Timing and Carbs, can not compensate for a non-marine grind
  3. jimmbo

    Camshaft specs. needed, modification feasible?

    Best bet, is to get a Marine Grind. I have seen far too many "RV/Truck" grinds, that just don't work well in Boats.
  4. jimmbo

    Batteries caught fire when connecting trolling motor

    Stuff at Rummage Sales is always Pristine, Better than New. Reading what you wrote, I would say, you answered your own Question
  5. jimmbo

    very cool carb and intake manifold causing moisture

    Ever take a Pitcher of Ice Water out of the Fridge on a very Humid Day? Ever notice how water is suddenly on the outside of the Pitcher? Same Thing is happening inside the Carb throat, Enough Ice can build up at the Throttle Plate and effectively seal the Carb closed. That was referred to as Icing.
  6. jimmbo

    Camshaft specs. needed, modification feasible?

    Likely Mercruiser # 431-811658 Duration @0.050": Intake 197; Exhaust 207 Lift: Intake .430; Exhaust .450 Lobe Centerline in degrees: Intake 106 ATDC; Exhaust 112 BTDC Lobe Separation in Degrees 109
  7. jimmbo

    How to decarb an outboard?

    Try doing that on a lot of Mercury Engines....
  8. jimmbo

    Mercury merc 110 9.8hp motor

    It is neat what Sunlight can do over a period of 45 yrs
  9. jimmbo

    How to decarb an outboard?

    Spraying any Water into a 2 Stroke, is right up there with the Stupidest Ideas Ever. Brake Fluid would also be in that list
  10. jimmbo

    Mercury merc 110 9.8hp motor

    It should also be on an Aluminium Disk on the Block, that looks like a Core Plug
  11. jimmbo

    Mercury merc 110 9.8hp motor

    When it was New, it looked like the one shown in Post #2
  12. jimmbo

    Old Evinrude question, Can anyone help?

    Looking at the Number Patterns, I came up with 1954 25hp, on his other thread with this engine in it
  13. jimmbo

    Mercury merc 110 9.8hp motor

    Welcome to iboats That Decal was used in 76 and 77. What's the Serial #?
  14. jimmbo

    Evinrude 60hp - 3 Blade vs 4 Blade Prop Pitch

    Calling Lake was well known for Walleye. Spent my Teenage Summers at that lake.
  15. jimmbo

    Evinrude 60hp - 3 Blade vs 4 Blade Prop Pitch

    What about McCloud Lake between Whitecourt and Swan Hills? You could also head towards Barhead, where Lac la none, is, and Lac St. Anne a few miles further on.
  16. jimmbo

    Intermittent Start - Starflite 75

    You can't use Muffs on that engine, so running it in a Tank is the only way. There was a device marketed that clamped on to the Exhaust Snout, where the Water Intake was located, but they are few and far between these days. Fuel Level in the Carb might be low, making it hard to start. That...
  17. jimmbo

    1978 Mercury 140 low compression

    I also second the idea of a wonky Compression Tester Gauge. I don't think it would run at all with those compression numbers. I guess if someone ran it without oil in the Gas, all cylinders could be pooched, evenly. A couple cans of Merc Power Tune, or BRP Engine Cleaner will help free up any...
  18. jimmbo

    35 HP - Never had Charging even though it's electric Start? Is this possible??

    Looking at the Parts list for that Serial #, there is a Charging Stator and a Retifier. Whether or not it is an User/Dealer installed Accessory, I don't know
  19. jimmbo

    Hard To Shift

    Have you adjusted the Idle Speed? Too much Preload on the Throttle Cable, can certainly affect the Ease of Shift
  20. jimmbo

    1970 Johnson 40hp 40e 70a spark plug

    A lot of the Sloughs, that are called Lakes in Alberta, have Walleye
Top