Search results

  1. alldodge

    Engine cut out while slowing down....

    I would use the 93, the 130 would be over torque so it has to be a misprint Your serial number comes up 1982 to 1984 3.0
  2. alldodge

    Engine cut out while slowing down....

    In manual 3 shows it to be torqued in 3 passes to 130 ft lb Passes 55, 90 to 130 Unable to find it in manual 10 Manual 13 list 90 ft lb In any case, if the head was flat within .003 and the correct gasket was used, it would be higher then what your seeing. Measure the height of the valve...
  3. alldodge

    Engine cut out while slowing down....

    Agree with Mike, and with compression that low I would be looking at the head again
  4. alldodge

    Random alarm 5.7L carb'd Bravo 2

    No harm in unplugging Its not a computer driver motor
  5. alldodge

    electric fuel pump problems

    Check kill switch After the key switch (turns power ON) it goes to the kill switch (man overboard) then to MPR fuse then MPR
  6. alldodge

    Random alarm 5.7L carb'd Bravo 2

    The TBV and knock module might be mounted to the exhaust elbow This is the knock sensor https://forums.iboats.com/attachments/img_7237-1-jpg.337926/ Your switch is this one on the right, and does look kind of rusty
  7. alldodge

    Fuel gauge issues

    Your previous sender may be a powered type, similar to Centroid products. Need to understand what is there or could change over to the 2 wire type but this would take another gauge (if what you have is a powered sender)
  8. alldodge

    Boat trailer to utility trailer?

    I took a single axle bass boat, put a deck on it that flips open in the middle with bunks. Its a flat deck for light hauling and flip the middle open and my seadoo rides on it
  9. alldodge

    Engine starts and dies.

    The 5V line is critical. Any one sensor which draws to much current can cause an issue with the others It might be a simple as a loose or unconnected ground wire on the harness. One small ground wire not making a good connection can cause other sensor issues
  10. alldodge

    Princess 286 hull spray rail had a hole, soaked with water

    The big IF. If its just in the channel then no harm, if its made it into the hull and the foam, then there is an issue. Water will work its way thru bottom pant, gelcoat and glass. Just should know if it did
  11. alldodge

    Princess 286 hull spray rail had a hole, soaked with water

    Drill test holes inside down in the bilge area down low
  12. alldodge

    Princess 286 hull spray rail had a hole, soaked with water

    Just what I have seen thru the years. Once water starts getting in, it doesn't take long. You could drill some test holes (6 to 8mm) in like the engine stringers and transom to see. The foam soaks up water fairly easy. My cruiser started with a small leak in the water tank, and by the time...
  13. alldodge

    Electric fuel pump issues

    Not the point I was making. The starter should have the extra post on the starter so could just wire it up without a relay and only use a oil pressure switch Saying it could, not saying it would
  14. alldodge

    Princess 286 hull spray rail had a hole, soaked with water

    Welcome aboard Terminology issue, we call that the lifting strakes. With water in that area, most likely the entire hull may need to be gutted. It won't dry out completely no mater how long its left open. The foam is most likely soaked and needs to be removed. Mold will start to grow and it...
  15. alldodge

    Electric fuel pump issues

    Thanks for the SN, the starter (Gen V 92 to 94) should have the extra terminal. So it could be wired up as in the first pic Would need to understand how yours is wired and what might be the best way to change.
  16. alldodge

    Fuel guage and tilt guage not working 88 nordic

    Both gauges have power, a ground and a sender wire. Sounds like the Tilt is working, its just the sender is grounding out. The gauges require 240 ohm (down or empty) to 33 ohm (up or full) senders. If the sender wire is grounded the gauge shows up or full. The tilt gauge bottoming out...
  17. alldodge

    Fuel guage and tilt guage not working 88 nordic

    Without more info, look for a fuse or broken wire
  18. alldodge

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    The 3200 rpm could be the In-Gear switch but your not getting an alarm. The switch is on the shift plate and you can disconnect it to see if the issue goes away Would be best to scan for codes, but without need fuel pressure reading
  19. alldodge

    Engine starts and dies.

    Code 0342 - Camshaft sensor lost. Motor will not run with this fault Code 0643 - 5V high. This is set when 5V reference is above 5.4V. I'm not seeing in the print out where it list above 5V, but if a sensor is failing it can cause the 5V level an issue. If 5V level is out of tolerance the...
  20. alldodge

    Engine starts and dies.

    I'm looking though them and compairing to the manual. Will get back with once my review is done
Top