Search results

  1. alldodge

    1992 Mercruiser 454 low oil pressure

    Agree, need to pull the motor
  2. alldodge

    Help with DPS-B 1.95 outdrive

    Its probably not the fuel or filter, but never hurts to check That is wierd, I enter your SN and it shows up as a V6-255-A but not parts show up under it. Hey @muc have an idea?
  3. alldodge

    Help with DPS-B 1.95 outdrive

    I would get the motor scanned for codes Being a 2014 its probably a CAT motor. It may be a fuel pressure isuue or other but need to scan to see what shows up Has the fuel filter been replaced this season? Could remove the fuel filter and dump contents into a clear container to see if there is...
  4. alldodge

    1992 Mercruiser 454 low oil pressure

    Howdy Lets start off with what is the motor serial number? My first thought is its the gauge or the sender. An issue with that is the alarm going off with low pressure, being the gauge sender and alarm sender are normally different (having S/N of motor will verify) Get a mechanical pressure...
  5. alldodge

    U Joint Replacement Quality (Made in China)

    In many cases China can be cheap knock offs, but not in all cases. If China made them to Meyle specs then IMO there good. I would probably use them
  6. alldodge

    Help with DPS-B 1.95 outdrive

    Remember there are 2 cables. The one on the shift plate just shifts the drive. The throttle cable goes straight to the TB
  7. alldodge

    Help with DPS-B 1.95 outdrive

    With the engine not going above idle, need to check the motor. Is throttle linkage still connected? Is this a drive by wire or does it have a cable connected to the throttle body? Can the motor be reved up in neutral?
  8. alldodge

    Merc 7.4l 454 Gen 4 to 5 interchangeable?

    You can use an auto one, but even fresh will corrode it over time. Will take a while but will work. The Edelbrock 7161 is $327 Or Weiand Stealth 8019 is $281 Both at Summitt. Look for 16 bots on the intake
  9. alldodge

    Maxum 25.5 leaning

    Sorry either don't understand, or have not seen an I/O that can manually be moved forward or back as a unit, only the trim IN/OUT Can you post a pic?
  10. alldodge

    Merc 7.4l 454 Gen 4 to 5 interchangeable?

    That clears it up, you have oval port vortec heads Here is one which will work Edelbrock 2561 and carb adapter 2732 Edlebrock shows out of stock, but places like summit racing and others indicate they do have them. I would call before placing order...
  11. alldodge

    Maxum 25.5 leaning

    OK its like a SCR You say drives are in a fixed position, meaning once adjusted for speed while on plane, there fixed or they do not trim? Assuming trimmed and then the issue starts. The tabs should be close to the sides and yours are If I'm load heavy on my 27PC I have to keep the drive fully...
  12. alldodge

    Merc 7.4l 454 Gen 4 to 5 interchangeable?

    I believe the heads should be rectangular ports and not oval. Can you verify?
  13. alldodge

    Maxum 25.5 leaning

    Not able to find a Maxum 25.5 If its a bow rider then to much weight in the bow. Is the drive being trimmed out any or staying tucked in?
  14. alldodge

    PWC's on the ohio ideas

    ^^ Agree. The USCG marks the rivers for anything less then 9 feet
  15. alldodge

    1998 Volvo Penta 4.3L GL

    Need a rebuild or another motor.
  16. alldodge

    Merc 7.4l 454 Gen 4 to 5 interchangeable?

    Being Fresh water you could go with aluminum
  17. alldodge

    5.7 Venturi Cluster

    Your probably correct but I have always called them emulsion tubes. I'll go back to my first comment. A remanufacture or someone had replaced one of the tubes during a rebuild, most likely from finding one damaged. I would say they need to be the same so each side gets the same amount of fuel...
  18. alldodge

    Anyone here interested in Japanese kitchen knives?

    Really, wow thanks
  19. alldodge

    New Seat COvers on PWC

    First time for everything, but never even thought about seat covers for a PWC. They would mean the seat and the cover would be wet. Then cover needs to be removed and dried so mold won't grow
  20. alldodge

    Anyone here interested in Japanese kitchen knives?

    I just use a steel on ours before each use
Top