Search results

  1. Faztbullet

    Adjusting 2015 20 HP Merc on 2014 Lowe 1467 WT

    Motor is nowhere close to being correct, it needs to be raise at least 2-3 inches. This is you water problem as the red line need to be where yellow line is...
  2. Faztbullet

    Drive Shaft damage on 2001 Evinrude

    This........
  3. Faztbullet

    Propping help with Jackplate!!

    100.... your good. You still have some upward adjustment to go, just watch the water pressure gauge. I guess this is too high also :)
  4. Faztbullet

    Getting ready to work on the 140

    On a crossflow when you shave head all you are doing is placing piston eyebrow closer to top of head and you might get 1-3 psi increase. To increase compression you increase the deflector size in head which reduces the combustion area in head. See pics below as Hi compression head has thick...
  5. Faztbullet

    Torque specs for exhaust manifold/divider plate

    Nope.... you need to follow torque pattern as you also have the divider spaghetti seal that need to be flattened evenly also. Tighten the bolts in a 3 steps 60,120,180inLbs. here is link..http://corboatracing.com/downloads/mercury-2.0-liter-torque-specs-2.pdf Really No!!! You do not want to use...
  6. Faztbullet

    1981 75hp evinrude sport

    Post a pic of it..
  7. Faztbullet

    1995 Johson 150 fast strike throttle linkage problem

    Make sure the sync and link is correct as a hot foot with incorrect stop can knock it out of wack and bind. Pic's below show incorrect and correct setting.
  8. Faztbullet

    Spark plug repair kit issue.

    Remove the Helicoil and install a Keensert......
  9. Faztbullet

    Mercury xr4 fuel issues

    Uhmmm..... what is # 1 then???
  10. Faztbullet

    1994 xri 200 bogging down

    Here do bench test....
  11. Faztbullet

    1996 Johnson 200-250 question. Can I make a 225 into a 250?

    That is a exhaust can.. a tuner is like pic below......
  12. Faztbullet

    1985 Mercruiser 260 - Conflicting Info - Thermostat Install

    Should be like this.......
  13. Faztbullet

    Ficht throttle linkage issue, please help with finding part

    PM me your address and will send ya one, just ask you repay shipping.....
  14. Faztbullet

    1986 Evinrude 90 V4 Running Rough

    You need to study up your electrical as a Hall sensor has power to the transducer and magnet triggers it to discharge. A outboard trigger has NO voltage to it as the encapsulated coil generates the positive voltage as the magnet passes by as the SCR in pack only triggers on a positive charge...
  15. Faztbullet

    cable ties for fuel hose clamps inside the motor?

    Never use a conventional ties on fuel line as they will not pull down in a full clamping circle. Only use the ties for fuel lines as they have a ramp and pull full tension around hose.I use BRP ties as I get em cheap...
  16. Faztbullet

    What is this???

    No belt or camshaft.....
  17. Faztbullet

    HELP!!!!! 1988 MERCURY 150HP WIRING DIAGRAM

    How long as this motor been setting without cowling as all the wires/connectors are UV damaged??? Even the fuel lines look old and dry and wire are disconnected ??? Heres a diagram.
  18. Faztbullet

    Needing Mercury XR4 Voltage Regulator

    Found it!!!! It ohms as per the limited testing, heres what I will do...PM me your address and will ship it USPS to you, hook it up and if works send me what you think its worth, if it don't work throw it away....
  19. Faztbullet

    going to look at a 07 225 etec, what all should I check/test?

    Next question is how it works.......see below.
  20. Faztbullet

    going to look at a 07 225 etec, what all should I check/test?

    I have thrown housings away that looked nearly new due to them being out of alignment. If a unit chits a pinion for no reason(impact,low/no oil,contaminated oil) you can bet its warped and you can rebuild it and it will live about 10-15 hours before it pukes again...
Top